KEIHIN 16010-5BF-305
Direct Fuel Injector Honda Civic Type R FK8 FL5 Accord 2.0T K20C1 FJ1220
16010-5BF-315, FJ1220--200 bar peak rail pressureProduct Overview
The 16010-5BF-305 is an original equipment (KEIHIN) precision component engineered specifically for the Honda 2.0L Turbocharged DOHC 16V VTEC Direct Injection (K20C1 / K20C4). Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0300, P0301, P0171, P0172.
Always verify the OE reference 160105BF315, FJ1220 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 16010-5BF-305 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 16010-5BF-305 |
| Manufacturer Brand | KEIHIN |
| Component Type | Direct Fuel Injector |
| Engine Application | Honda 2.0L Turbocharged DOHC 16V VTEC Direct Injection (K20C1 / K20C4) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 12 N-m (106 lb-in) |
| Fuel Line / Rail Torque | 25 N-m (18 lb-ft) |
| Primary Diagnostic Fault Codes | P0300, P0301, P0171, P0172 |
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 12 N-m (106 lb-in), and torque fuel line fittings to 25 N-m (18 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Tighten the injector mounting/hold-down to 12 N·m.
- Tighten the high-pressure line to 25 N·m.
- Confirm the system pressure is 200 bar and the part number is 16010-5BF-305 before installation.
Frequently Asked Questions
Will this injector fit my Honda Civic FK8/FL5, Accord 10th Gen, or Acura RDX 3rd Gen?
It is listed for the Honda 2.0L VTEC Turbo Earth Dreams K20C1/K20C4/K20C6 engine family. Listed fitment is Honda Civic FK8/FL5 2017-2025, Honda Accord 10th Gen 2018-2022, and Acura RDX 3rd Gen 2019-2023. Confirm the exact application against the vehicle's EPC before ordering.
What diagnostic trouble codes are associated with this gasoline direct-injection injector?
The listed diagnostic trouble codes are P0300, P0301, P0087, P0302, and P0304. No specific symptom list is provided in the verified facts, so use these codes only as diagnostic clues and confirm the faulty unit before replacement.
Do I need coding/adaptation or new seals for this injector?
Coding/adaptation requirements and seal reuse guidance are not stated in the verified facts. Both must be confirmed against the vehicle's EPC before installation.
How can I verify the old injector before ordering a replacement?
Check the old injector for part number 16010-5BF-305 and compare it with the listed cross references 160105BF305, 160105BF315, FJ1220, 160105MSH00, and 164505BFA01. If the markings are unclear, confirm the part against the vehicle's EPC before ordering.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.