KEIHIN 16010-5MS-H00
Fuel Injector Honda Civic Type R FK8 FL5 Acura RDX TLX 2.0T K20C1 K20C4
16010-5MS-H15, 06160-5MS-H00, FJ1274--200 bar peak rail pressureProduct Overview
The 16010-5MS-H00 is an original equipment (KEIHIN) precision component engineered specifically for the Honda 2.0L VTEC Turbo Earth Dreams DOHC 16V (K20C1 / K20C4). Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0300, P0301, P0171, P0172.
Always verify the OE reference 160105MSH15, 061605MSH00, FJ1274 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 16010-5MS-H00 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 16010-5MS-H00 |
| Manufacturer Brand | KEIHIN |
| Component Type | Direct Fuel Injector |
| Engine Application | Honda 2.0L VTEC Turbo Earth Dreams DOHC 16V (K20C1 / K20C4) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 12 N-m (9 lb-ft) |
| Fuel Line / Rail Torque | 32 N-m (24 lb-ft) |
| Primary Diagnostic Fault Codes | P0300, P0301, P0171, P0172 |
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 12 N-m (9 lb-ft), and torque fuel line fittings to 32 N-m (24 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Verify 16010-5MS-H00 and the listed cross references against the vehicle’s EPC before ordering.
- Tighten the hold-down to 12 N·m and the high-pressure line to 32 N·m.
- Confirm coding/adaptation and seal-reuse requirements against the vehicle’s EPC before installation.
Frequently Asked Questions
Will this injector fit my Honda Civic FK8/FL5, Accord 10th Gen, or Acura RDX 3rd Gen?
This gasoline direct-injection injector, part 16010-5MS-H00, is listed for the Honda 2.0L VTEC Turbo Earth Dreams K20C1 / K20C4 / K20C6 engine family in Civic FK8/FL5 2017-2025, Accord 10th Gen 2018-2022, and Acura RDX 3rd Gen 2019-2023. Confirm the exact vehicle and engine against the vehicle’s EPC before ordering.
What DTCs are listed for this injector?
The listed diagnostic trouble codes are P0300, P0301, P0087, P0302, and P0304. No further symptom details are stated here, so confirm diagnosis against the vehicle’s EPC before replacing parts.
What are the mounting and high-pressure line torque specs?
The mounting / hold-down torque is 12 N·m, the high-pressure line torque is 32 N·m, and the system pressure is 200 bar.
How can I verify the old injector part number?
Check the old injector for 16010-5MS-H00 and compare it with the listed cross references 160105MSH00, 160105MSH15, 061605MSH00, FJ1274, and 160105BF305. If the markings are unclear, confirm fitment against the vehicle’s EPC before ordering.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.