KEIHIN 16010-RLV-315
Direct Fuel Injector Honda Pilot Ridgeline Passport Odyssey Acura MDX 3.5L V6 J35Y
16010-RLV-305, 06160-RLV-305, FJ1298, 16010-RLV-316--200 bar peak rail pressureProduct Overview
The 16010-RLV-315 is an original equipment (KEIHIN) precision component engineered specifically for the Honda 3.5L Earth Dreams i-VTEC Direct Injection DOHC 24V V6 (J35Y6). Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0300, P0301, P0171, P0172.
Always verify the OE reference 16010RLV305, 06160RLV305, FJ1298, 16010RLV316 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 16010-RLV-315 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 16010-RLV-315 |
| Manufacturer Brand | KEIHIN |
| Component Type | Direct Fuel Injector |
| Engine Application | Honda 3.5L Earth Dreams i-VTEC Direct Injection DOHC 24V V6 (J35Y6) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 12 N-m (106 lb-in) |
| Fuel Line / Rail Torque | 22 N-m (16 lb-ft) |
| Primary Diagnostic Fault Codes | P0300, P0301, P0171, P0172 |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 12 N-m (106 lb-in), and torque fuel line fittings to 22 N-m (16 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Torque the injector mounting/hold-down to 12 N·m.
- Torque the high-pressure line to 22 N·m.
- Confirm fitment against the vehicle’s EPC before ordering or installation.
Frequently Asked Questions
Will this injector fit my Honda or Acura 3.5L Earth Dreams i-VTEC V6?
Part 16010-RLV-315 is a gasoline direct-injection injector listed for Honda Pilot, Ridgeline, Passport, and Odyssey with J35Y6/J35Y7 (2016-2023), and Acura MDX/TLX with J35Y5/J35Y6 (2014-2020). Confirm fitment against the vehicle’s EPC before ordering.
What diagnostic trouble codes are listed for this injector?
The listed DTCs are P0300, P0301, P0087, P0302, and P0304. No additional symptom or diagnostic criteria are provided, so confirm diagnosis against the vehicle’s EPC/service information.
Does this injector require coding or adaptation?
No coding or adaptation data is listed for part 16010-RLV-315. Confirm any coding or adaptation requirement against the vehicle’s EPC/service information before installation.
How can I verify the old injector part number?
Compare the old injector’s stamped number with 16010-RLV-315 and the listed cross references: 16010RLV315, 16010RLV305, 06160RLV305, FJ1298, 16010RLV316, and 167905J6305. If the stamping is unclear, confirm against the vehicle’s EPC before ordering.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.