KEIHIN 16790-5J6-305
High Pressure Fuel Pump Honda Pilot Ridgeline Odyssey Acura MDX 3.5L V6 J35Y
16790-5J6-315, HM10036, GDP106--200 bar peak rail pressureProduct Overview
The 16790-5J6-305 is an original equipment (KEIHIN) precision component engineered specifically for the Honda-Acura 3.5L i-VTEC Direct Injection SOHC 24V V6 (J35Y6 / J35Y5). Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P0171, P0191.
Always verify the OE reference 167905J6315, HM10036, GDP106 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 16790-5J6-305 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 16790-5J6-305 |
| Manufacturer Brand | KEIHIN |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Honda-Acura 3.5L i-VTEC Direct Injection SOHC 24V V6 (J35Y6 / J35Y5) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 12 N-m (106 lb-in) |
| Fuel Line / Rail Torque | 33 N-m (24 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P0171, P0191 |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 12 N-m (106 lb-in), and torque fuel line fittings to 33 N-m (24 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Verify part number 16790-5J6-305 and the listed cross references before installation.
- Torque the mounting / hold-down to 12 N·m.
- Torque the high-pressure line to 33 N·m.
Frequently Asked Questions
Will this high-pressure fuel pump fit my Honda Pilot or Acura MDX?
It is listed for Honda Pilot / Ridgeline / Passport / Odyssey with J35Y6 or J35Y7 (2016-2023) and Acura MDX / TLX with J35Y5 or J35Y6 (2014-2020). It is a gasoline direct-injection high-pressure fuel pump for the Honda / Acura 3.5L Earth Dreams i-VTEC V6 (J35Y5 / J35Y6). Confirm exact fitment against the vehicle’s EPC before ordering.
What part number and cross references identify this pump?
The part number is 16790-5J6-305, and the listed cross references are 167905J6305, 167905J6315, HM10036, GDP106, and 16010RLV315. It is a gasoline direct-injection high-pressure fuel pump. Confirm any interchange details against the vehicle’s EPC before ordering.
What system pressure and torque values apply to this pump?
The listed system pressure is 200 bar, the mounting / hold-down torque is 12 N·m, and the high-pressure line torque is 33 N·m. These are the only pressure and torque values provided for this component. Confirm the procedure against the vehicle’s EPC before work.
What fault codes are listed for this pump, and does it need coding or adaptation?
The listed diagnostic trouble codes are P0300, P0087, P0193, P0089, and P0191. No coding or adaptation requirement is stated in the verified facts; confirm that against the vehicle’s EPC instead of guessing.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.