KEIHIN 16450-RNA-A01
Multi Point Fuel Injector Honda Civic 8 9 HR V 1.8L i VTEC R18A1 R18Z1 R18Z9 FJ786
16450-RNA-J01, FJ786, 842-12328--4 bar peak rail pressureProduct Overview
The KEIHIN 16450-RNA-A01 is a precision automotive OE replacement component engineered specifically for Honda 1.8L i-VTEC SOHC R18A1 / R18Z1 / R18Z9 powertrains. Designed to deliver consistent calibration and factory-specified fuel atomization, this unit restores original throttle response, diagnostic rail pressure stability, and emission compliance.
Always verify the OE reference 16450RNAJ01, FJ786, 84212328 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 16450-RNA-A01 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| part_number | 16450-RNA-A01 |
| oem_reference | 16450-RNA-A01 |
| manufacturer | KEIHIN |
| system_type | Fuel Injector |
| pressure_rating | 3.5 bar (50 psi) |
| operating_temperature | -40°C to +135°C |
| flange_mount_torque | 12 N-m (9 lb-ft) |
| high_pressure_line_torque | 12 N-m (9 lb-ft) |
| diagnostic_dtc | P0171, P0300, P0301, P0172 |
Installation Tips
- Depressurize the fuel system completely via diagnostic scan tool or by removing the fuel pump fuse prior to line disassembly.
- Clean all surrounding bracket areas thoroughly using residue-free brake cleaner to prevent abrasive particulate ingress.
- Inspect the mechanical camshaft lobe and roller follower or clean injector bore seating surfaces before hardware alignment.
- Install component using fresh factory O-rings or Teflon combustion chamber seals lubricated only with clean motor oil.
- Torque mounting flange fasteners in alternating increments to 12 N-m (9 lb-ft).
- Torque high-pressure hydraulic tube fittings using a calibrated flare nut wrench to 12 N-m (9 lb-ft).
- Prime low-pressure fuel circuit, cycle ignition key 3-4 times, and inspect for high-pressure hydraulic leaks before road test.
- Always replace single-use high-pressure metal fuel lines and micro-filter seals whenever disconnected.
- Verify camshaft driving lobe surfaces for scoring or flat spots before installing any mechanical pump.
- Reset long-term and short-term fuel trim adaptations via OBD-II diagnostic scanner after physical replacement.
Frequently Asked Questions
Will this injector fit my Honda Civic or HR-V?
This 16450-RNA-A01 multi-point (port) fuel injector is listed for Honda Civic VIII/IX FD1/FA1/FB2/FK2 with R18A1/R18A2/R18Z1 (2006-2015) and Honda HR-V II RU1 / Civic X with R18Z9/R18ZA (2015-2021). Confirm the exact application against the vehicle's EPC before ordering.
What cross-reference numbers can I use to verify the old injector?
The listed cross references are 16450RNAA01, 16450RNAJ01, FJ786, and 84212328. This part is a multi-point (port) fuel injector for the Honda 1.8L i-VTEC SOHC R18A1 / R18Z1 / R18Z9 engine family. Confirm the old part against the vehicle's EPC before replacement.
What diagnostic trouble codes are listed for this injector?
The verified diagnostic trouble codes are P0300, P0301, P0087, P0302, and P0304. No additional symptom or diagnosis procedure is stated in the verified facts; confirm diagnosis and application against the vehicle's EPC.
What are the installation torques and is coding or adaptation required?
Mounting/hold-down torque is 12 N·m and high-pressure line torque is 12 N·m; system pressure is 4 bar. No coding/adaptation or seal-reuse requirement is stated in the verified facts, so confirm those points against the vehicle's EPC before installation.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.