DENSO 23209-31090
Fuel Injector Toyota Camry Highlander Sienna RAV4 Lexus RX350 ES350 3.5L V6 2GR FE 23209 0P040
23209-0P040, 23209-31070, FJ746, 842-12328, 23250-31090HIGH-SPEED SATURATED ELECTROMAGNETIC SOLENOID PLUNGER12-Hole High-Atomization Micro-Droplet Director Nozzle3 bar peak rail pressureProduct Overview
The Denso 23209-31090 (superseding part number 23209-0P040, interchangeable with 23209-31070, Toyota production stamping 23250-31090, and aftermarket references FJ746 and 842-12328) is the genuine original equipment 12-hole multi-port fuel injector engineered for Toyota's acclaimed 3.5-liter 2GR-FE V6 engine family. Delivering 295 cc/min of precisely calibrated fuel flow through a 12-micro-hole atomization plate at 3.0 bar, this injector powers tens of millions of prominent vehicles including the Toyota Camry V6 (2007-2017), Highlander 3.5L (2008-2016), Sienna minivan (2007-2016), RAV4 V6 (2006-2012), Avalon (2005-2018), and Lexus RX350 and ES350 (2007-2018).
Always verify the original manufacturer reference stamped on your component before ordering. For 23209-31090, inspect matching OE cross-references and ensure related high-pressure seals, followers, or grommets are renewed during service.
Technical Specifications
| Specification | Value |
|---|---|
| System Type | Toyota Multi-Point Electronic Fuel Injection (EFI Port Injection) |
| Base Regulated Fuel Pressure | 3.1 - 3.5 bar (45 - 51 psi / 310 - 350 kPa system pressure) |
| Static Fuel Flow Rate | 295 cc/min @ 3.0 bar (28.1 lb/hr gasoline fuel delivery) |
| Coil Electrical Resistance | 11.6 - 12.4 Ohms @ 20°C (High-Impedance Saturated Solenoid) |
| Nozzle Spray GeometryCore Spec | |
| Fuel Delivery Pipe Mounting Fasteners | 21 N·m (15 lb-ft) securing aluminum rail to lower intake |
| Upper & Lower Seals Architecture | Upper Viton Fluorocarbon O-Ring & Lower Intake Manifold Grommet |
| Operating Voltage Range | 9.0 - 16.0 Volts DC |
| Manufacturer | Denso Corporation (Tier-1 OEM for Toyota Motor Corporation) |
| Denso Production Reference | Denso Japan / Toyota 23209-31090 / 23209-0P040 |
| Operating PressureCore Spec |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- EFI Fuel System Pressure Relief: Remove the 15A EFI fuse from the engine compartment junction block. Crank engine for 5 seconds to depressurize fuel rails, then disconnect negative battery terminal.
- Upper Intake Plenum & Throttle Body Removal: Unbolt upper aluminum intake surge tank plenum, rear stay brackets, PCV lines, and throttle body. Remove plenum to expose fuel delivery rails on both cylinder banks.
- Fuel Delivery Pipe Mounting Bolts Removal: Disconnect electrical wiring harness connectors from all six fuel injectors. Remove the 12mm bolts securing Bank 1 and Bank 2 fuel delivery pipes to the lower intake manifold.
- Injector Extraction & Intake Manifold Grommet Replacement: Carefully draw fuel rails backwards and remove injectors from rail pockets. Extract hardened lower rubber insulator grommets from intake manifold injector counterbores.
- New O-Ring Lubrication, Reassembly & Specified Torquing: Lubricate new upper Viton O-rings with clean engine oil. Push injectors into delivery pipe with a smooth twisting motion. Torque fuel delivery pipe bolts to 21 N·m (15 lb-ft) and reinstall intake plenum.
- Verify the engine code and listed model-year coverage against the vehicle’s EPC before ordering part number 23209-31090.
- Use the listed torques of 21 N·m for mounting/hold-down and 21 N·m for the high-pressure line during installation.
- Match the old unit against part number 23209-31090 and the listed cross references before replacement.
Frequently Asked Questions
Will this multi-point fuel injector fit my Toyota/Lexus 3.5L V6?
This multi-point (port) fuel injector, part number 23209-31090, is listed for Toyota/Lexus 3.5L V6 2GR-FKS, 2GR-FXS, and 2GR-FE engines. Listed applications include Camry/Avalon (2005-2018), Highlander/Sienna (2007-2016), RAV4/Venza (2006-2015), and Lexus RX/ES (2007-2018). Confirm the exact engine code and model year against the vehicle’s EPC before ordering.
What diagnostic trouble codes are listed for this injector?
The verified diagnostic trouble codes listed are P0300, P0301, P0087, P0302, and P0304. The provided facts do not state other failure symptoms, so use the vehicle’s service information for diagnosis.
Do I need to code or adapt this injector after installation?
The provided facts do not state any coding or adaptation procedure for this multi-point (port) fuel injector. Confirm coding/adaptation requirements against the vehicle’s EPC or service information before installation.
Can I reuse the seals when installing this injector?
The provided facts do not state seal reuse or replacement guidance for this injector. Confirm the required seals and replacement instructions against the vehicle’s EPC.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.