BOSCH 13517595339
High Pressure Fuel Pump Mini Cooper S JCW R55 R56 R57 R58 R59 R60 1.6T N18 0261520144
13517595338, 7595339, 0261520145, HPP0036, 0261520144--150 bar peak rail pressureProduct Overview
The 13517595339 is an original equipment (BOSCH) precision component engineered specifically for the BMW-Mini 1.6L Prince TwinPower Turbo DOHC 16V I4 (N18B16A). Operating at peak injection pressures up to 150 bar (2175 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P10ED, P2880.
Always verify the OE reference 13517595338, 7595339, HPP0036 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 13517595339 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 13517595339 |
| Manufacturer Brand | BOSCH |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | BMW-Mini 1.6L Prince TwinPower Turbo DOHC 16V I4 (N18B16A) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 12 N-m (106 lb-in) |
| Fuel Line / Rail Torque | 26 N-m (19 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P10ED, P2880 |
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 12 N-m (106 lb-in), and torque fuel line fittings to 26 N-m (19 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Confirm the Mini platform, engine code, and model year against the listed fitment before ordering.
- Tighten the pump mounting/hold-down fasteners to 12 N·m.
- Tighten the high-pressure line to 26 N·m.
Frequently Asked Questions
Will part number 13517595339 fit my Mini?
It is listed for Mini Clubman (R55), Hatchback (R56), and Cabrio (R57) with N18B16A or N18B16C engines from 2010-2015, and for Mini Coupe, Roadster, Countryman, and Paceman (R58/R59/R60/R61) with N18B16A from 2011-2016. Cross references include 13517595338, 7595339, 0261520145, HPP0036, and 0261520144. Confirm your exact vehicle against its EPC before ordering.
What diagnostic trouble codes are associated with this high-pressure fuel pump?
The listed diagnostic trouble codes are P0300, P0087, P0193, P0089, and P0191. Use these codes as diagnostic leads rather than proof that the pump alone is faulty. Any additional diagnosis or symptom interpretation must be confirmed against the vehicle's service information.
Does this high-pressure fuel pump require coding or adaptation after installation?
Coding or adaptation requirements are not stated in the verified facts, so they must be confirmed against the vehicle's EPC or service instructions. The listed installation torques are 12 N·m for the mounting/hold-down and 26 N·m for the high-pressure line. The system pressure is 150 bar.
Can I reuse the seals, and how can I verify the old pump?
Seal reuse is not stated in the verified facts and must be confirmed against the vehicle's EPC or service instructions. To verify the old part, compare its part number and markings with 13517595339 and the listed cross references: 13517595338, 7595339, 0261520145, HPP0036, and 0261520144. If the markings do not match, confirm fitment against the EPC rather than guessing.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.