Catalog / BOSCH / 13517616170
BOSCH

BOSCH 13517616170

View Specs
SolenoidGDI High-Pressure Fuel Pump (HPFP)Euro 6

High Pressure Fuel Pump BMW 335i 435i 535i M235i M2 M3 M4 F30 F10 F80 F82 3.0L N55 S55 0261520144

Reference data for BOSCH 13517616170 high-pressure fuel pump · OEM 13517594419, 13517592881, 0261520144, 0261520143, GDP104, HM10014 · Application BMW N20 / N26 / N55 / S55 (2.0L & 3.0L TwinPower Turbo)
OE REFERENCE13517594419, 13517592881, 0261520144, 0261520143, GDP104, HM10014
CONTROL VALVEINTEGRATED ELECTROMAGNETIC DIGITAL FLOW QUANTITY CONTROL VALVE
NOZZLE-
EMISSIONEuro 6
WARRANTY12 Months
01

Product Overview

The Bosch 13517616170 (Bosch reference 0261520144, superseding BMW part numbers 13517594419 and 13517592881) is the factory OEM mechanical high-pressure fuel pump (HPFP) developed for BMW's flagship 3.0-liter turbocharged N55 and twin-turbocharged S55 inline-six engines. Delivering rail pressures up to 200 bar (2900 psi), this camshaft-actuated single-plunger pump meters fuel across high-performance applications including the BMW 335i (F30), 435i (F32), 535i (F10), M235i (F22), M2 (F87), X5 35i (F15), M3 (F80), and M4 (F82). Failure of the N55/S55 high-pressure fuel pump typically presents with progressive internal plunger seal wear or digital quantity control solenoid sticking. Symptoms begin with prolonged cold engine cranking (5 to 10 seconds), sudden engine hesitation during wide-open throttle boost transitions, and the vehicle entering reduced-power limp mode with a 'Drivetrain Malfunction' iDrive alert. Stored diagnostic trouble codes include BMW specific codes 11A002 (Fuel high pressure, cold start: Pressure too low), 11A004 (Fuel high pressure during delivery: Pressure too low), 2BF8, and standard OBD-II code P0087. Professional installation requires strict adherence to BMW service specifications. Technicians must replace the pump flange Viton O-ring, align the internal drive shaft tang, and tighten the two flange bolts evenly to 13 N·m (115 in-lb). The high-pressure steel flare nut must be torqued to 25 N·m (18.4 lb-ft) while counter-holding the outlet adapter. Always cycle the low-pressure priming circuit prior to engine ignition.

Before You Order

Always verify the OE reference 13517594419, 13517592881, GDP104, HM10014 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 13517616170 needs no ECU calibration coding; no code transfer is required after fitting.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
BMW 3 Series / 4 Series / 2 SeriesBMW N20 / N26 / N55 / S55 (2.0L & 3.0L TwinPower Turbo)2012-2016
BMW M2 F87BMW N20 / N26 / N55 / S55 (2.0L & 3.0L TwinPower Turbo)2016-2018
BMW M3 (F80) / M4 (F82)BMW N20 / N26 / N55 / S55 (2.0L & 3.0L TwinPower Turbo)2015-2020
04

Technical Specifications

SpecificationValue
System TypeBMW HPI 200-bar High-Pressure Direct Gasoline Injection
Operating Fuel Pressure200 bar (20 MPa / 2900 psi nominal peak rail pressure)
Pump MechanismAuxiliary Vacuum/Camshaft Shaft-Driven Single-Piston Plunger
Mounting Flange Fastener Torque13 N·m (115 in-lb) M8 Torx flange bolts
High-Pressure Steel Line Flare Nut25 N·m (18.4 lb-ft) rigid steel rail delivery pipe union
Low-Pressure Feed Line Union15 N·m (11 lb-ft) threaded low-pressure supply connection
Internal Quantity Control SolenoidPulse-width modulated 12V digital metering valve
ManufacturerBosch (Tier-1 OEM for BMW Group)
Bosch Production Reference0261520144 / 0261520143

Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)

Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.

BOSCHExact Engine & Chassis Match
0261500109
Gasoline Direct Injection (GDI) • 200 bar
🚙 Engine Code N20
Technical Specifications & Pinout
BOSCHExact Engine & Chassis Match
13647597870
Gasoline Direct Injection (GDI) • 200 bar
🚙 Engine Code N20
Technical Specifications & Pinout
05

Installation Tips

  1. Low-Pressure Fuel System Depressurization & Battery Disconnect: Remove fuse for in-tank electric fuel pump (EKPS module) in trunk power distribution box. Crank engine until it stalls to exhaust residual pressure, then disconnect negative battery terminal.
  2. Intake Charge Pipe & Engine Acoustic Shield Removal: Remove upper engine acoustic beauty cover, disconnect MAP sensor harness, and unclamp driver-side intercooler charge pipe elbow to gain direct access to the HPFP under the intake manifold.
  3. High-Pressure Steel Line & Low-Pressure Quick Connect Removal: Counter-hold pump outlet fitting with a 17mm open wrench while loosening the steel delivery pipe flare nut with a flare-nut wrench. Disconnect quick-release low-pressure supply line.
  4. Mounting Bolts Removal & HPFP Extraction: Evenly loosen the two E-Torx flange mounting bolts in alternating half-turns against internal plunger spring tension. Extract pump carefully and inspect internal drive flange coupling.
  5. New Viton O-Ring Installation, Torquing & Pre-Start Priming: Install brand-new Viton radial O-ring lubricated with clean engine oil. Torque mounting bolts evenly to 13 N·m (115 in-lb) and metal flare nut to 25 N·m (18.4 lb-ft). Cycle ignition three times for 10 seconds before starting.
Tips & Warnings:
  • Always counter-hold the pump body outlet adapter: Loosening or tightening the metal line flare nut without holding the body hex will shear the pump internal thread boss.
  • Never reuse the rubber flange O-ring: Reusing an aged radial seal causes severe oil leakage down the engine block onto the steering rack.
  • Inspect drive coupling teeth: Inspect the camshaft-driven drive tang; if teeth show fretting wear, replace the intermediate drive cup to prevent sudden pump seizure.
  • Mandatory ignition pre-priming: Turn ignition ON without pressing brake pedal for 10 seconds three times to run the low-pressure pump and purge all air pockets before first crank.
06

Frequently Asked Questions

QWhat vehicles does part number 13517616170 fit, and what part numbers cross-reference it?

It is listed for BMW 3 Series, 4 Series, and 2 Series (2012-2016); BMW M2 F87 (2016-2018); and BMW M3 F80 / M4 F82 (2015-2020), for the BMW N20 / N26 / N55 / S55 engine family (2.0L & 3.0L TwinPower Turbo). Cross references listed are 13517616170, 13517594419, 13517592881, 0261520144, 0261520143, and GDP104. Confirm fitment against the vehicle’s EPC before ordering.

QWhat are the mounting and high-pressure line torque specifications?

The mounting / hold-down torque is 13 N·m. The high-pressure line torque is 25 N·m. This is a gasoline direct-injection high-pressure fuel pump listed at 200 bar system pressure.

QWhat symptoms or diagnostic trouble codes point to a failed high-pressure fuel pump?

The diagnostic trouble codes listed for this part are P0300, P0087, P0193, P0089, and P0191. Symptom descriptions beyond these codes are not stated in the supplied facts, so confirm diagnosis against the vehicle’s EPC before replacing parts.

QDoes this high-pressure fuel pump require coding or adaptation after installation?

The supplied facts do not state coding or adaptation requirements for this high-pressure fuel pump. Confirm the required procedure against the vehicle’s EPC before installation.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0088Critical

Fuel Rail/System Pressure Too High

P0089Critical

Fuel Pressure Regulator 1 Performance

P0191Critical

Fuel Rail Pressure Sensor 'A' Circuit Range/Performance

P0002High

Fuel Volume Regulator Control Circuit Range / Performance (VCV / IMV)

P0090High

Fuel Pressure Regulator 1 Control Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

COMMON RAIL WORKSHOP DIAGNOSTICS

Common Rail High-Pressure Pump Diagnostics Guide

Diagnose common rail high-pressure pump failure: suction vacuum, CP4 roller glitter, plunger wear, air ingress & P0087 hard start. Workshop bench testing.

Read Technical Protocol
COMMON RAIL WORKSHOP DIAGNOSTICS

Fuel Metering Valve (IMV/SCV) Diagnostics Guide

Diagnostic guide for common rail fuel metering valves (IMV/SCV/FCA/MPROP). Normally open vs closed, coil resistance, PWM duty cycle & P0088 / P0089 test.

Read Technical Protocol
OBD-II DIAGNOSTIC PROTOCOL

P0087 Low Rail Pressure Diagnosis Guide

Step-by-step workshop diagnostic protocol for OBD-II DTC P0087 (Fuel Rail Pressure Too Low). 5-stage troubleshooting tree: backleak testing, SCV valve, PRV valve, and high-pressure pump.

Read Technical Protocol
COMMON RAIL WORKSHOP DIAGNOSTICS

Rail Pressure Relief Valve Diagnostics Guide

Common rail pressure relief valve (PRV) testing guide. Diagnose hot start stalls, P0087 rail pressure loss, return line leakage & single vs 2-stage valves.

Read Technical Protocol