Catalog / BOSCH / 16600-1KC0A
BOSCH

BOSCH 16600-1KC0A

View Specs
SolenoidGasoline Direct Injection (GDI / HDEV)Euro 6

High Pressure Fuel Injector Nissan Juke Tiida MR16DDT 1.6 DIG T Turbo

Reference data for BOSCH 16600-1KC0A common rail injector · OEM 16600-1KC0B, 0261500091, 0261500092, HDEV-5-2 · Application Nissan MR16DDT / Renault M5M (1.6L DIG-T Turbo GDI)
OE REFERENCE16600-1KC0B, 0261500091, 0261500092, HDEV-5-2
CONTROL VALVEHIGH-PRESSURE ELECTROMAGNETIC SOLENOID NEEDLE VALVE
NOZZLE-
EMISSIONEuro 6
WARRANTY12 Months
01

Product Overview

The Bosch 16600-1KC0A is a Bosch HDEV5 gasoline direct injection multi-hole injector for Nissan MR16DDT and Renault M5M 1.6L DIG-T turbo GDI engines. It is listed for the Nissan Juke F15 1.6 DIG-T (2010-2019), Tiida / Pulsar C12 (2011-2018) and Renault Clio IV R.S. 200 EDC (2013-2019). Direct injection pressure is 150 bar (15 MPa / 2175 psi), with a multi-hole spray targeted at the piston crown bowl and coil resistance of 1.4-1.8 Ω at 20°C. Fuel rail clamping bolts take 21 N·m and the high-pressure feed line flare nut 30 N·m. Common codes are P0171, P0300 and P0301-P0304. Replace Teflon combustion seal ring CM-5250 and lubricate the fuel rail O-ring with clean motor oil.

Before You Order

Always verify the OE reference 166001KC0B, HDEV52 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 16600-1KC0A needs no ECU calibration coding; no code transfer is required after fitting.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Nissan Juke F15 1.6 DIG-TNissan MR16DDT / Renault M5M (1.6L DIG-T Turbo GDI)2010-2019
Nissan Tiida / Pulsar (C12)Nissan MR16DDT / Renault M5M (1.6L DIG-T Turbo GDI)2011-2018
Renault Clio IV R.S. 200 EDCNissan MR16DDT / Renault M5M (1.6L DIG-T Turbo GDI)2013-2019
04

Technical Specifications

SpecificationValue
System TypeBosch HDEV-5 Gasoline Direct Injection Multi-Hole Injector
Operating PressureCore Spec
Spray PatternMulti-hole targeted spray pattern towards piston crown bowl
Fuel Rail Bolt Torque21 N·m Fuel Rail Clamping Bolts
High Pressure Feed Line Torque30 N·m Flare Nut Connection
Coil Resistance1.4 - 1.8 Ω at 20°C (Direct peak-and-hold driver circuit)
Common Fault CodesP0171 (System Too Lean Bank 1), P0300 (Random Misfire), P0301-P0304 (Cylinder Misfire)
Workshop PrecautionReplace Teflon combustion seal ring CM-5250 and lubricate fuel rail O-ring with clean motor oil

Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)

Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.

HITACHIExact Engine & Chassis Match
16630-1KC0C
Gasoline Direct Injection (GDI) • 150 bar
🚙 Nissan Juke F15 1.6 Dig-T (M5M)
Technical Specifications & Pinout
05

Installation Tips

  1. Release Fuel Pressure & Remove Charge Pipes: Depressurize high-pressure fuel circuit. Disconnect intercooler charge piping and intake runners to access the high-pressure fuel rail.
  2. Remove High Pressure Rail Assembly: Disconnect electrical wiring harness clips. Undo rail mounting bolts (21 N·m) and withdraw fuel rail with injectors from the cylinder head.
  3. Replace Teflon Chamber Seals & Viton O-Rings: Remove old Teflon seal using plastic pick. Stretch new Teflon ring over guide cone and compress into groove. Install new viton rail O-rings.
  4. Reinstall Rail & Torque Fasteners: Lubricate upper O-rings with clean engine oil. Insert injectors squarely into cylinder head bores. Torque fuel rail bolts to 21 N·m and fuel line to 30 N·m.
Tips & Warnings:
  • Always confirm the application against the EPC using 16600-1KC0A before ordering.
  • Inspect the connector, harness and seal area during replacement, and follow the workshop manual for any adaptation steps.
  • Keep the work area clean during installation, because this is a petrol direct-injection injector and contamination can cause faults.
06

Frequently Asked Questions

QWhich vehicles is this listed for?

16600-1KC0A is listed for the Nissan Juke DIG-T, Nissan Tiida/Pulsar and Renault Clio R.S. applications shown, but confirm fitment by VIN or EPC before ordering.

QWhat should I check before ordering?

Confirm the vehicle is the listed gasoline direct-injection application, compare the removed injector with 16600-1KC0A, and check connector and seal condition; verify any coding or adaptation requirements in the workshop manual.

QDoes the replacement injector need coding or matching?

Coding or adaptation requirements are not stated for 16600-1KC0A; check the vehicle's EPC or workshop manual and follow the listed diagnostic or adaptation procedure before returning the vehicle to service.

QWhat are symptoms of a failed unit?

Symptoms are not stated for this unit; use the vehicle's workshop data to confirm an injector fault before replacement, and do not assume the injector is the cause without proper diagnosis.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0200Critical

Fuel Injector Circuit Malfunction (General / Common Driver Stage)

P0201Critical

Injector Circuit Malfunction - Cylinder 1

P0300Critical

Random or Multiple Cylinder Misfire Detected

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

COMMON RAIL WORKSHOP DIAGNOSTICS

Fuel Metering Valve (IMV/SCV) Diagnostics Guide

Diagnostic guide for common rail fuel metering valves (IMV/SCV/FCA/MPROP). Normally open vs closed, coil resistance, PWM duty cycle & P0088 / P0089 test.

Read Technical Protocol
OBD-II DIAGNOSTIC PROTOCOL

P0087 Low Rail Pressure Diagnosis Guide

Step-by-step workshop diagnostic protocol for OBD-II DTC P0087 (Fuel Rail Pressure Too Low). 5-stage troubleshooting tree: backleak testing, SCV valve, PRV valve, and high-pressure pump.

Read Technical Protocol
DIESEL WORKSHOP DIAGNOSTIC SOP

Cylinder Balance & Injector Deviation Guide

Common rail diesel cylinder balance & smooth running diagnostic guide. Balance rates, mg/stroke deviation, P0263 misfire, compression vs injector test.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol