HITACHI 16630-1KC0C
High Pressure Fuel Pump Nissan Juke F15 Tiida GTS Renault Clio RS 1.6T MR16DDT HPP0019
16630-1KC0A, 16630-1KC0B, HPP0019--150 bar peak rail pressureProduct Overview
The 16630-1KC0C is an original equipment (HITACHI) precision component engineered specifically for the Nissan / Renault 1.6L DIG-T Turbocharged DOHC 16V MR16DDT (M5M). Operating at peak injection pressures up to 150 bar (2175 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P0171, P2293.
Always verify the OE reference 166301KC0A, 166301KC0B, HPP0019 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 16630-1KC0C needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 16630-1KC0C |
| Manufacturer Brand | HITACHI |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Nissan / Renault 1.6L DIG-T Turbocharged DOHC 16V MR16DDT (M5M) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 11 N-m (97 lb-in) |
| Fuel Line / Rail Torque | 28 N-m (21 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P0171, P2293 |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 11 N-m (97 lb-in), and torque fuel line fittings to 28 N-m (21 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Confirm the pump part number and vehicle application against the EPC before ordering.
- Check for petrol leaks and connector condition before installation, following the workshop manual.
- Use the vehicle's workshop data for fastener torque and any coding or adaptation steps.
Frequently Asked Questions
Will this pump fit my Nissan Juke, Tiida/Pulsar or Renault Clio R.S. EDC?
It is listed for the Nissan Juke, Nissan Tiida/Pulsar and Renault Clio R.S. EDC applications shown for part 16630-1KC0C; confirm your exact vehicle against the EPC or workshop data before ordering.
What symptoms indicate the high-pressure fuel pump has failed?
Symptoms are not specified for this pump; diagnose high-pressure petrol delivery faults using the vehicle's workshop manual and confirm the fault before replacing part 16630-1KC0C.
What should I check before ordering this pump?
Confirm the vehicle application, engine variant and pump part number against the EPC or workshop manual; also verify the old unit's fitment and any listed coding or adaptation requirements before ordering.
Does the replacement pump need to be matched or adapted to the vehicle?
Coding or adaptation requirements are not stated for this pump. Confirm them against the vehicle's EPC or workshop manual before installation, and do not assume plug-and-play operation.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.