Catalog / HITACHI / 16600-1LA0A
HITACHI

HITACHI 16600-1LA0A

View Specs
SolenoidGasoline Direct Injection (GDI / HDEV)Euro 6

High Pressure Direct Fuel Injector Infiniti Q50 Q60 3.0T VR30DDTT QX80 Patrol 5.6L V8 VK56VD 166001LA0A

Reference data for HITACHI 16600-1LA0A common rail injector · OEM 16600-EY00A, 16600-1LA0B, FIJ0039 · Application Nissan / Infiniti 3.0L Twin-Turbo V6 VR30DDTT & 5.6L V8 VK56VD
OE REFERENCE16600-EY00A, 16600-1LA0B, FIJ0039
CONTROL VALVEHIGH-RESPONSE MULTI-HOLE ELECTROMAGNETIC HIGH-PRESSURE NOZZLE
NOZZLE-
EMISSIONEuro 6
WARRANTY12 Months
01

Product Overview

The Hitachi 16600-1LA0A (superseding part number 16600-EY00A) is the genuine Tier-1 original equipment high-pressure direct fuel injector engineered for Nissan and Infiniti's advanced direct-injection powerplants. Primarily found in the high-performance 3.0-liter Twin-Turbo V6 (VR30DDTT) powering the Infiniti Q50 and Q60, as well as the heavy-duty 5.6-liter Endurance V8 (VK56VD) in the Infiniti QX80, Nissan Patrol Y62, Armada, and Titan, this 150-bar (2175 psi) electromagnetic injector delivers ultra-fine fuel atomization under extreme thermal loads. On higher-mileage vehicles, direct injection tip carbonization and internal pintle micro-leakage result in common drivability issues. Drivers frequently encounter diagnostic trouble codes P0300 (Random/Multiple Cylinder Misfire Detected), P0301 through P0308 (Specific Cylinder Misfires), and rich condition codes P0172 / P0175. The root cause is typically gasoline weeping past the valve seat into the combustion chamber after hot shutdown, causing severe cold-start extended cranking, black exhaust smoke, and catalytic converter overheating. Professional installation mandates replacement of single-use high-pressure metal pipes and Teflon combustion washers. Fuel rail retaining bolts must be torqued to 10 N·m (89 in-lb), while fuel pipe flare nuts require 28 N·m (21 lb-ft). Technicians must inspect engine oil for gasoline odor and change the oil filter immediately if fuel dilution is detected.

Before You Order

Always verify the OE reference 16600EY00A, 166001LA0B, FIJ0039 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 16600-1LA0A needs no ECU calibration coding; no code transfer is required after fitting.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Infiniti Q50 / Q60Nissan / Infiniti 3.0L Twin-Turbo V6 VR30DDTT & 5.6L V8 VK56VD2016-2024
Infiniti QX80Nissan / Infiniti 3.0L Twin-Turbo V6 VR30DDTT & 5.6L V8 VK56VD2014-2024
Nissan Patrol / ArmadaNissan / Infiniti 3.0L Twin-Turbo V6 VR30DDTT & 5.6L V8 VK56VD2010-2024
04

Technical Specifications

SpecificationValue
System TypeNissan Direct Injection Gasoline (DIG) 150-bar System
Operating PressureCore Spec
Spray ConfigurationHigh-Pressure Laser Multi-Hole Symmetrical Spray Pattern
Injector Hold-Down Bolt Torque10 N·m (89 in-lb) fuel rail mounting bolts📐 Torque & Angle Wizard →
Fuel Line Nut Torque28 N·m (21 lb-ft) high-pressure delivery pipe flare nut
Combustion SealHigh-Density Virgin PTFE Combustion Ring
Upper Rail SealingFluorocarbon (FKM) High-Temp Viton O-Ring
ManufacturerHitachi Astemo (Tier-1 OEM for Nissan Motor Co.)
OEM Production Number16600-1LA0A / FIJ0039

Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)

Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.

HITACHIExact Engine & Chassis Match
16630-1LA0B
Gasoline Direct Injection (GDI) • 150 bar
🚙 Infiniti Q50 / Q60 (VK56VD)
Technical Specifications & Pinout
HITACHIExact Engine & Chassis Match
16630-5CA0A
Gasoline Direct Injection (GDI) • 200 bar
🚙 Engine Code VK56VD
Technical Specifications & Pinout
05

Installation Tips

  1. Fuel System Residual Pressure Relief: Remove fuel pump fuse from IPDM E/R fuse box. Crank engine for 5 seconds until it stalls, then disconnect negative battery terminal.
  2. Engine Cover & Intercooler Piping Removal: On VR30DDTT twin-turbo engines, remove top decorative shroud and unbolt water-to-air charge coolers to access fuel rail assemblies.
  3. Rigid High-Pressure Fuel Feed Pipe Disconnection: Loosen high-pressure metal fuel supply pipe union nuts with a 17mm flare nut wrench. Discard single-use flared pipe per Nissan FSM directives.
  4. Fuel Rail Extraction & Combustion Chamber Bore Cleaning: Unbolt fuel rail retaining fasteners. Pull rails and injectors straight out. Inspect cylinder head injector bores and remove soot with brass brush.
  5. New Injector Insertion & Torquing Protocol: Coat upper O-rings with clean engine oil (keep lower PTFE rings clean and dry). Push injectors into rail, torque rail bolts to 10 N·m (89 in-lb), and pipe nuts to 28 N·m (21 lb-ft).
Tips & Warnings:
  • Never lubricate the lower PTFE combustion seal: Oil degrades the Teflon seal, causing high-pressure combustion blow-by and melted injector bodies.
  • Inspect spark plugs on corresponding cylinders: A dripping injector washes fuel down the cylinder, fouling the plug and triggering misfire codes even after injector replacement.
  • Verify low-pressure feed pressure: Ensure the tank lift pump delivers stable 5.0 to 6.5 bar (72 to 94 psi) before diagnosing high-pressure injector issues.
  • Never reuse high-pressure crossover lines: Metallic flare ends yield upon tightening; reusing them causes dangerous high-pressure fuel sprays onto exhaust manifolds.
06

Frequently Asked Questions

QWill part number 16600-1LA0A fit my Infiniti or Nissan?

This is a gasoline direct-injection injector for the Nissan/Infiniti 3.0L Twin-Turbo V6 VR30DDTT and 5.6L V8 VK56VD engine families. Listed fitment is Infiniti Q50/Q60 (2016-2024), Infiniti QX80 (2014-2024), and Nissan Patrol/Armada (2010-2024). Confirm by VIN and the vehicle's EPC before ordering.

QWhat diagnostic trouble codes are listed for this injector?

The diagnostic trouble codes listed for this injector are P0300, P0301, P0087, P0302, and P0304. If these codes are present, confirm the diagnosis against the vehicle's service information and EPC because the listing does not provide symptom details.

QWhat are the mounting and high-pressure line torque specifications?

Mounting/hold-down torque is 10 N·m, and high-pressure line torque is 28 N·m. The system pressure listed for this gasoline direct-injection injector is 150 bar.

QDoes this injector need coding/adaptation, and how do I verify the old part number?

Coding/adaptation requirements are not stated in the verified facts; confirm them against the vehicle's EPC or service information. Cross references listed are 166001LA0A, 16600EY00A, 166001LA0B, FIJ0039, 0261500162, and 06E906036E. If the old injector number does not match these, confirm fitment against the vehicle's EPC.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0200Critical

Fuel Injector Circuit Malfunction (General / Common Driver Stage)

P0201Critical

Injector Circuit Malfunction - Cylinder 1

P0300Critical

Random or Multiple Cylinder Misfire Detected

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

COMMON RAIL WORKSHOP DIAGNOSTICS

Fuel Metering Valve (IMV/SCV) Diagnostics Guide

Diagnostic guide for common rail fuel metering valves (IMV/SCV/FCA/MPROP). Normally open vs closed, coil resistance, PWM duty cycle & P0088 / P0089 test.

Read Technical Protocol
OBD-II DIAGNOSTIC PROTOCOL

P0087 Low Rail Pressure Diagnosis Guide

Step-by-step workshop diagnostic protocol for OBD-II DTC P0087 (Fuel Rail Pressure Too Low). 5-stage troubleshooting tree: backleak testing, SCV valve, PRV valve, and high-pressure pump.

Read Technical Protocol
DIESEL WORKSHOP DIAGNOSTIC SOP

Cylinder Balance & Injector Deviation Guide

Common rail diesel cylinder balance & smooth running diagnostic guide. Balance rates, mg/stroke deviation, P0263 misfire, compression vs injector test.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol