HITACHI 16630-1LA0B
High Pressure Fuel Pump Nissan Patrol Y62 Armada Infiniti QX80 5.6L V8 VK56VD
16630-1LA0A, HPP0022--150 bar peak rail pressureProduct Overview
The 16630-1LA0B is an original equipment (HITACHI) precision component engineered specifically for the Nissan-Infiniti 5.6L V8 VVEL Direct Injection (VK56VD). Operating at peak injection pressures up to 150 bar (2175 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P0171, P0191.
Always verify the OE reference 166301LA0A, HPP0022 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 16630-1LA0B needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 16630-1LA0B |
| Manufacturer Brand | HITACHI |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Nissan-Infiniti 5.6L V8 VVEL Direct Injection (VK56VD) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 21 N-m (15 lb-ft) |
| Fuel Line / Rail Torque | 28 N-m (21 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P0171, P0191 |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 21 N-m (15 lb-ft), and torque fuel line fittings to 28 N-m (21 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Confirm the vehicle’s engine code and fitment against the EPC before ordering this 16630-1LA0B high-pressure fuel pump.
- Tighten the pump mounting/hold-down fasteners to 21 N·m.
- Tighten the high-pressure line to 28 N·m.
Frequently Asked Questions
Will this high-pressure fuel pump fit my Infiniti Q50/Q60?
This pump, part number 16630-1LA0B, is listed for Infiniti Q50/Q60 (2016-2024), Infiniti QX80 (2014-2024), and Nissan Patrol/Armada (2010-2024) with the VR30DDTT or VK56VD engine family. Confirm the exact engine code and model year against the vehicle’s EPC before ordering.
What DTCs can point to a failed high-pressure fuel pump?
The listed diagnostic trouble codes for this gasoline direct-injection high-pressure fuel pump are P0300, P0087, P0193, P0089, and P0191. Use these codes as diagnostic leads and confirm the fault against the vehicle’s service information and EPC rather than guessing.
What are the mounting and high-pressure line torque specs for this pump?
The mounting/hold-down torque for this high-pressure fuel pump is 21 N·m, and the high-pressure line torque is 28 N·m. Confirm any additional fastener specifications against the vehicle’s EPC/service information.
How can I verify the old pump and cross-reference the replacement?
The listed cross references for this pump are 166301LA0B, 166301LA0A, HPP0022, and 166001LA0A, in addition to part number 16630-1LA0B. Compare the old pump’s markings and confirm the replacement against the vehicle’s EPC before installation.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.