Catalog / DENSO / 16600-JK20A
DENSO

DENSO 16600-JK20A

View Specs
SolenoidMulti-Point Port Fuel Injection (MPI / EV14)Euro 5

Multi Port Fuel Injector Infiniti G37 Q50 Q60 G35 FX35 Nissan 370Z Maxima 3.5L 3.7L VQ37VHR VQ35HR

Reference data for DENSO 16600-JK20A common rail injector · OEM 16600-JK20B, FJ1027, 842-12348, 297500-0540 · Application Nissan/Infiniti 3.7L VQ37VHR VVEL & 3.5L VQ35HR DOHC 24V Naturally Aspirated V6
OE REFERENCE16600-JK20B, FJ1027, 842-12348, 297500-0540
CONTROL VALVE12-HOLE HIGH-DISPERSAL MICRO-DROPLET ATOMIZATION DIRECTOR
NOZZLE-
EMISSIONEuro 5
WARRANTY12 Months
01

Product Overview

The Nissan 16600-JK20A (superseding part number 16600-JK20B, aftermarket reference FJ1027 and Denso manufacturing code 297500-0540) is the original equipment 12-hole multi-port fuel injector engineered for Nissan and Infiniti's iconic high-revving 3.7-liter VQ37VHR VVEL and 3.5-liter VQ35HR Dual-Intake V6 engines. Delivering an optimized 340 cc/min flow rate at 3.5 bar (50 psi), this high-impedance fuel injector is standard equipment across the Infiniti G37 (V36/CV36), Q50, Q60, G35 Sedan, FX35, EX35, M37, and the Nissan 370Z (Z34) and Maxima (A35). With extensive mileage and heat cycling inside tight engine bays, gummy fuel varnish and carbon deposits accumulate on the 12 laser-drilled micro-orifices. This restriction degrades fuel atomization from a fine mist into coarse droplets. Common driver symptoms include engine hesitation under wide-open throttle acceleration, rough erratic idle with A/C load, extended hot restart cranking, and diagnostic trouble codes P0300 (Random/Multiple Cylinder Misfire), cylinder-specific misfires (P0301 through P0306), and lean air-fuel ratio codes P0171 / P0174. Proper injector replacement demands removal of the upper intake plenum collector. Technicians should inspect and replace both the upper Viton fuel rail O-rings and lower manifold grommets, lubricating seals with clean engine oil. The fuel rail securing bolts require 10 N·m (89 in-lb), and the intake plenum fasteners must be torqued in cross-pattern to 11 N·m (97 in-lb). Verifying smooth rotational freedom before reassembly guarantees leak-free operation.

Before You Order

Always verify the OE reference 16600JK20B, FJ1027, 84212348, 2975000540 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 16600-JK20A needs no ECU calibration coding; no code transfer is required after fitting.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Infiniti G37 / Q50 / Q60Nissan/Infiniti 3.7L VQ37VHR VVEL & 3.5L VQ35HR DOHC 24V Naturally Aspirated V62008-2015
Nissan 370Z Z34Nissan/Infiniti 3.7L VQ37VHR VVEL & 3.5L VQ35HR DOHC 24V Naturally Aspirated V62009-2020
Infiniti G Sedan / FX / EXNissan/Infiniti 3.7L VQ37VHR VVEL & 3.5L VQ35HR DOHC 24V Naturally Aspirated V62007-2012
04

Technical Specifications

SpecificationValue
System TypeNissan ECCS Multi-Point Electronic Fuel Injection (MPI / PFI)
Operating Fuel Pressure3.5 bar (50 psi / 350 kPa regulated rail pressure)
Static Flow Rate340 cc/min @ 3.0 bar (32.4 lb/hr) high-performance calibration
Coil Electrical Resistance11.6 - 12.4 Ohms @ 20°C (High-Impedance Saturated Solenoid)
Spray Geometry12-Hole Laser Precision Split-Cone Micro-Atomization Director
Fuel Rail Fastener Torque10 N·m (89 in-lb) fuel rail mounting bolts
Intake Plenum Fastener Torque11 N·m (97 in-lb) upper intake manifold collector bolts
Seals ArchitectureUpper Viton Fluorocarbon O-Ring & Lower Resilient Intake Grommet
ManufacturerNissan Motor Co. / Denso (Tier-1 OEM)
Manufacturer Part Number16600-JK20A / 297500-0540
05

Installation Tips

  1. Fuel System Depressurization & Battery Disconnect: Remove fuel pump fuse (Fuse 15A) in IPDM E/R fuse box. Crank engine until it stalls to relieve rail pressure, then disconnect negative battery terminal.
  2. Upper Intake Manifold Collector (Plenum) Removal: Disconnect dual intake air ducts, throttle body harnesses, PCV breather hoses, and remove the upper intake plenum bolts in reverse order to expose the fuel rails.
  3. Fuel Rail Securing Bolts & Injector Harness Disconnection: Disconnect injector wiring harness push-connectors. Remove the four 10mm fuel rail mounting bolts securing the aluminum rails to the lower intake manifold.
  4. Fuel Rail Extraction & Lower Port Seal Inspection: Lift fuel rail assemblies straight upward evenly. Extract individual injectors from rail pockets and remove old lower rubber grommets from lower intake manifold holes.
  5. New O-Ring Lubrication, Installation & Sequence Torquing: Coat new upper Viton O-rings and lower intake grommets with clean engine oil. Push injectors into rails with a smooth twisting motion. Torque rail bolts to 10 N·m (89 in-lb) and plenum bolts to 11 N·m (97 in-lb).
Tips & Warnings:
  • Never use silicone-based spray or grease on O-rings: Silicone poisons oxygen sensors and catalytic converters; lubricate strictly with fresh engine oil or spindle oil.
  • Always replace lower manifold rubber grommets: Reusing hardened lower grommets creates severe vacuum leaks directly into intake ports, causing unmetered lean codes.
  • Verify injector free rotation: After rail installation, ensure all injectors can be smoothly rotated by hand 360° to verify O-rings are not pinched or cocked.
  • Observe plenum tightening sequence: When reinstalling the upper composite plenum, torque fasteners in factory spiral sequence to 11 N·m to avoid cracking plastic mounting tabs.
06

Frequently Asked Questions

QWill part number 16600-JK20A fit my Infiniti G37/Q50/Q60 or Nissan 370Z?

The listed fitment includes Infiniti G37/Q50/Q60 (2008-2015), Nissan 370Z Z34 (2009-2020), and Infiniti G Sedan/FX/EX (2007-2012). It is a multi-point (port) fuel injector for the Nissan/Infiniti 3.7L VQ37VHR VVEL and 3.5L VQ35HR DOHC 24V naturally aspirated V6 engine family. Confirm the exact vehicle/engine against the EPC before ordering.

QWhat diagnostic trouble codes are listed for this fuel injector?

The verified diagnostic trouble codes listed are P0300, P0301, P0087, P0302, and P0304. No additional symptom list is provided in the verified facts, so confirm diagnosis against the vehicle's EPC instead of guessing.

QWhat system pressure and torque values are listed for this injector?

The listed system pressure is 4 bar. Mounting/hold-down torque is 10 N·m, and high-pressure line torque is 10 N·m. Any other pressure or torque value must be confirmed against the vehicle's EPC instead of guessed.

QHow can I verify the old injector matches this replacement?

Compare the old unit with part number 16600-JK20A and the listed cross references: 16600JK20A, 16600JK20B, FJ1027, 84212348, 2975000540, and 166001KT0A. If the old number does not match, confirm fitment against the vehicle's EPC before ordering instead of guessing.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0200Critical

Fuel Injector Circuit Malfunction (General / Common Driver Stage)

P0201Critical

Injector Circuit Malfunction - Cylinder 1

P0300Critical

Random or Multiple Cylinder Misfire Detected

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

Workshop Diagnostic Protocol

Common Rail Injector Back-Leak Testing Guide

Common rail injector backleak test protocol. Graduated cylinder setup, warm idle & cranking limits in mL/min, control valve wear & P0087 diagnosis.

Read Technical Protocol
COMMON RAIL DIESEL WORKSHOP SOP

Stuck Injector Removal & Carbon Cleaning SOP | FuelPartsDB

Comprehensive workshop SOP for stuck diesel injector removal, pneumatic vibro-puller extraction, carbon solvent softening, and seat reaming without damage.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol