DENSO 16600-EN200
Multi Hole Fuel Injector Nissan Altima Rogue Sentra 2.5L QR25DE 2.0L MR20DE 297500 0540
16600-JA000, 297500-0540, FJ1056, 842-12344--4 bar peak rail pressureProduct Overview
The DENSO 16600-EN200 is a factory precision fuel injection component engineered specifically for the Nissan 2.5L DOHC 16V QR25DE & 2.0L DOHC MR20DE. Manufactured to strict original equipment tolerances, it delivers precise fuel atomization and operates up to its rated pressure of 3.5 bar (51 psi). Common operational failure symptoms that point directly to this assembly include: Persistent Diagnostic Trouble Codes such as P0171, P0300, P0301, P0172 stored in the ECM. Hard cold starting, erratic idle oscillations, and severe acceleration stumbling. Unburnt fuel smell in the exhaust, black tailpipe soot, or fuel dilution in the engine crankcase. Loss of high-RPM power and engine protection limp-mode activation under highway load.
Always verify the OE reference 16600JA000, 2975000540, FJ1056, 84212344 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 16600-EN200 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| sku | 16600-EN200 |
| brand | DENSO |
| manufacturer_code | 297500-0540 |
| pressure_rating | 3.5 bar (51 psi) |
| torque_flange | 9 N-m (80 lb-in) |
| torque_line | 28 N-m (21 lb-ft) |
| engine_family | Nissan 2.5L DOHC 16V QR25DE & 2.0L DOHC MR20DE |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Always replace single-use high-pressure fuel lines and Teflon/copper sealing washers before installation.
- Lubricate the pump roller tappet or injector O-rings with clean engine oil before guiding into place.
- Tighten mounting flange fasteners in an even criss-cross pattern to 9 N-m (80 lb-in).
- Hand-thread fuel rail fittings first, then torque high-pressure flare nuts to 28 N-m (21 lb-ft) using a calibrated crowfoot wrench.
- Cycle the low-pressure fuel pump multiple times and perform a physical leak inspection before engine ignition.
- Verify system pressure is 4 bar before diagnosing the multi-point fuel injector.
- Apply 9 N·m to the mounting/hold-down.
- Apply 28 N·m to the high-pressure line.
Frequently Asked Questions
Will part number 16600-EN200 fit my Nissan X-Trail T32, Qashqai J11, or Rogue Sport?
It is listed for Nissan X-Trail T32 2.0L MR20DE and 2.5L QR25DE (2014-2021), Qashqai J11 2.0L MR20DD (2014-2021), and Rogue Sport 2.0L MR20DD (2017-2022). For any other application, confirm against the vehicle’s EPC before ordering.
What diagnostic trouble codes are listed for this multi-point fuel injector?
The listed diagnostic trouble codes are P0300, P0301, P0302, P0304, and P0087. Use them as diagnostic clues and confirm the fault with proper diagnostics before replacing the injector.
After replacement, does this injector need coding or adaptation, and can I reuse the seals?
Coding/adaptation and seal reuse are not stated in the supplied facts; confirm both against the vehicle’s EPC instead of guessing. The mounting/hold-down torque is 9 N·m and the high-pressure line torque is 28 N·m.
How can I verify the old injector before ordering?
Check the old unit against part number 16600-EN200 and the listed cross references: 16600EN200, 16600JA000, 2975000540, FJ1056, 84212344, and 166001VA0A. If the marking does not match, confirm fitment against the vehicle’s EPC before ordering.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.