DENSO 23100-0T020
High Pressure Fuel Pump Toyota Corolla Levin C HR IZOA 1.2T D 4T 8NR FTS 297500 0220
23100-0T010, 297500-0220, HPP0025, GDP702--200 bar peak rail pressureProduct Overview
The 23100-0T020 is an original equipment (DENSO) precision component engineered specifically for the Toyota 1.2L Turbo DOHC 16V 8NR-FTS / 9NR-FTS D-4T. Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P0171, P119A.
Always verify the OE reference 231000T010, 2975000220, HPP0025, GDP702 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 23100-0T020 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 23100-0T020 |
| Manufacturer Brand | DENSO |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Toyota 1.2L Turbo DOHC 16V 8NR-FTS / 9NR-FTS D-4T |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 21 N-m (15 lb-ft) |
| Fuel Line / Rail Torque | 25 N-m (18 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P0171, P119A |
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 21 N-m (15 lb-ft), and torque fuel line fittings to 25 N-m (18 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Verify part number 23100-0T020 and cross references 231000T020, 231000T010, 2975000220, HPP0025, GDP702, and 2320936010 against the vehicle EPC before installation.
- Tighten the mounting/hold-down to 21 N·m and the high-pressure line to 25 N·m.
- Confirm coding/adaptation and seal-reuse requirements against the vehicle EPC before installation.
Frequently Asked Questions
Will part number 23100-0T020 fit my Toyota?
It fits Toyota Corolla/Auris/Levin (NRE185/ZRE210) with 8NR-FTS or 9NR-FTS (2015-2022) and Toyota C-HR/IZOA (NGX10/NGX50) with 8NR-FTS (2016-2022) in the Toyota 1.2L Turbo DOHC 16V 8NR-FTS/9NR-FTS D-4T engine family. Confirm the exact vehicle by VIN/EPC before ordering.
What pressure and torque values apply to this high-pressure fuel pump?
The system pressure is 200 bar, the mounting/hold-down torque is 21 N·m, and the high-pressure line torque is 25 N·m. Use these values only with the correct installation procedure for 23100-0T020.
Which diagnostic trouble codes are listed for this application?
The listed diagnostic trouble codes are P0300, P0087, P0193, P0089, and P0191. Treat them as diagnostic leads and confirm the root cause against the vehicle's EPC/service information.
Does this pump need coding or adaptation, and can I reuse the seals?
The provided facts do not state coding/adaptation or seal-reuse requirements for 23100-0T020. Confirm both against the vehicle's EPC/service information rather than guessing.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.