Catalog / DENSO / 23209-0V010
DENSO

DENSO 23209-0V010

View Specs
SolenoidMulti-Point Port Fuel Injection (MPI / EV14)Euro 5

Multi Point Fuel Injector Toyota Camry RAV4 Highlander Scion tC Lexus ES 2.5L 2AR FE 2.7L 1AR FE 23209 36010

Reference data for DENSO 23209-0V010 common rail injector · OEM 23209-36010, 23209-09140, 23280-36010, FJ1068 · Application Toyota 2.5L 2AR-FE & 2.7L 1AR-FE DOHC 16-Valve Dual VVT-i 4-Cylinder EFI
OE REFERENCE23209-36010, 23209-09140, 23280-36010, FJ1068
CONTROL VALVE12-HOLE PRECISION MULTI-ORIFICE MICRO-DROPLET ATOMIZER PLATE
NOZZLE-
EMISSIONEuro 5
WARRANTY12 Months
01

Product Overview

The Denso 23209-0V010 (Toyota reference 23209-36010, alternate part numbers 232090V010, 2320936010, and 23209-09140) is the original equipment 12-hole multi-port fuel injector engineered for Toyota's bulletproof 2.5-liter 2AR-FE and 2.7-liter 1AR-FE Dual VVT-i engines. Operating at a regulated fuel pressure of 47 psi (3.24 bar) with an optimized 280 cc/min static flow rate, this high-impedance saturated injector fuels millions of popular vehicles globally, including the Toyota Camry (XV50), RAV4 (XA40), Highlander (XU50), Venza, Scion tC, and Lexus ES 250. Over extensive operating lifespans, low-quality fuels and heat cycles create lacquer and gummy varnish within the internal micro-filter basket and 12-hole atomizer plate. Drivability concerns manifest as rough morning idle, sluggish acceleration, poor fuel economy, and diagnostic trouble codes P0300 (Random/Multiple Cylinder Misfire), specific cylinder misfires (P0301 through P0304), and lean air-fuel ratio code P0171 (System Too Lean Bank 1). Hardened lower intake manifold insulators can also create vacuum leaks. Proper replacement adheres to Toyota technical standards. Technicians should replace both upper Viton O-rings and lower rubber vibration grommets, lubricating seals with fresh engine oil prior to insertion. The fuel rail mounting bolts require 9 N·m (80 in-lb). Confirming that all injectors rotate freely by hand ensures proper O-ring alignment before pressurizing the fuel system.

Before You Order

Always verify the OE reference 2320936010, 2320909140, 2328036010, FJ1068 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 23209-0V010 needs no ECU calibration coding; no code transfer is required after fitting.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Toyota Camry (XV50) / RAV4 (XA40)Toyota 2.5L 2AR-FE & 2.7L 1AR-FE DOHC 16-Valve Dual VVT-i 4-Cylinder EFI2012-2018
Toyota Highlander / VenzaToyota 2.5L 2AR-FE & 2.7L 1AR-FE DOHC 16-Valve Dual VVT-i 4-Cylinder EFI2009-2019
Toyota Scion tC (AGT20)Toyota 2.5L 2AR-FE & 2.7L 1AR-FE DOHC 16-Valve Dual VVT-i 4-Cylinder EFI2011-2018
Lexus ES (XV60)Toyota 2.5L 2AR-FE & 2.7L 1AR-FE DOHC 16-Valve Dual VVT-i 4-Cylinder EFI2011-2018
04

Technical Specifications

SpecificationValue
System TypeToyota Electronic Fuel Injection (EFI) Multi-Port Port Injection
Operating Fuel Pressure3.24 bar (47 psi / 324 kPa regulated)
Static Flow Rate280 cc/min @ 3.0 bar (26.6 lb/hr)
Electrical Resistance11.6 - 12.4 Ohms @ 20°C (High-Impedance Saturated Solenoid)
Spray Geometry12-Hole Precision Multi-Dispersal Micro-Atomization Director
Fuel Rail Fastener Torque9 N·m (80 in-lb) fuel rail mounting bolts
Seals ArchitectureUpper Viton Fluorocarbon O-Ring & Lower Resilient Vibration Insulator
ManufacturerDenso Corporation (Tier-1 OEM for Toyota Motor Corporation)
Denso Production Reference23209-0V010 / 23209-36010
05

Installation Tips

  1. Fuel System Residual Pressure Relief: Remove EFI fuse (20A) in engine bay fuse box. Crank engine until it stalls to deplete line pressure, then disconnect negative battery terminal.
  2. Engine Appearance Cover & Vacuum Hose Removal: Unclip engine decorative acoustic cover, disconnect PCV breather hoses, and unclip fuel injector wiring harness connectors.
  3. Quick-Connect Fuel Feed Line Disconnection: Release plastic fuel pipe lock retainer and disconnect low-pressure feed line using fuel line disconnect tool. Catch remaining drips with shop towel.
  4. Fuel Rail Fastener Removal & Rail Extraction: Remove two 10mm fuel rail mounting bolts. Pull fuel rail and injectors straight out from intake manifold ports, taking care not to lose rubber insulators.
  5. New O-Ring Lubrication, Installation & Torquing: Coat new upper O-rings and lower vibration insulators with clean engine oil or spindle oil. Push injectors into rail with a gentle twist. Reinstall rail and torque bolts to 9 N·m (80 in-lb).
Tips & Warnings:
  • Always replace lower manifold vibration insulators: Hardened lower rubber insulators allow unfiltered unmetered air into intake ports, causing persistent P0171 lean codes.
  • Never use silicone sealant or grease: Lubricate O-rings strictly with fresh engine oil or spindle oil to prevent silicone contamination of oxygen sensors.
  • Verify injector free rotation: After snapping injectors into the fuel rail, verify that each injector rotates smoothly by hand without binding.
  • Prime fuel circuit prior to ignition: Turn ignition switch ON for 5 seconds twice without cranking to pressurize system and confirm zero fuel seepage.
06

Frequently Asked Questions

QWill this injector fit my 2012-2018 Camry/RAV4, 2009-2019 Highlander/Venza, 2011-2018 Scion tC, or 2011-2018 Lexus ES?

Part number 23209-0V010 is listed for those applications: Camry (XV50) / RAV4 (XA40) 2012-2018, Highlander / Venza 2009-2019, Scion tC (AGT20) 2011-2018, and Lexus ES (XV60) 2011-2018 with the Toyota 2.5L 2AR-FE & 2.7L 1AR-FE DOHC 16-Valve Dual VVT-i 4-Cylinder EFI engine family. If your exact vehicle is not in that list, confirm against the vehicle's EPC.

QWhich DTCs are listed, and what symptoms should I expect?

The diagnostic trouble codes listed with this part are P0300, P0301, P0087, P0302, and P0304. Specific symptoms are not stated in the verified facts, so diagnose before replacing the multi-point (port) fuel injector.

QWhat are the installation torque specs and system pressure?

For this multi-point (port) fuel injector, the mounting/hold-down torque is 9 N·m and the high-pressure line torque is 9 N·m. The system pressure is 3 bar. Any additional torque value or installation detail not stated here must be confirmed against the vehicle's EPC.

QHow can I verify the old injector, and are seal reuse or coding/adaptation details stated?

Check for part number 23209-0V010 and compare it with cross references 232090V010, 2320936010, 2320909140, 2328036010, FJ1068, and 2310025010. Seal reuse and coding/adaptation requirements are not stated in the verified facts, so confirm those against the vehicle's EPC.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0200Critical

Fuel Injector Circuit Malfunction (General / Common Driver Stage)

P0201Critical

Injector Circuit Malfunction - Cylinder 1

P0300Critical

Random or Multiple Cylinder Misfire Detected

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

Workshop Diagnostic Protocol

Common Rail Injector Back-Leak Testing Guide

Common rail injector backleak test protocol. Graduated cylinder setup, warm idle & cranking limits in mL/min, control valve wear & P0087 diagnosis.

Read Technical Protocol
COMMON RAIL DIESEL WORKSHOP SOP

Stuck Injector Removal & Carbon Cleaning SOP | FuelPartsDB

Comprehensive workshop SOP for stuck diesel injector removal, pneumatic vibro-puller extraction, carbon solvent softening, and seat reaming without damage.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol