BOSCH 31686560
High Pressure Fuel Pump Volvo XC90 XC60 S90 V90 2.0L Drive E T6 Twincharged 0261520295
31478796, 31375549, 0261520295, 0261520476INTEGRATED HIGH-SPEED DIGITAL FLOW CONTROL VALVE (FCV)-200 bar peak rail pressureProduct Overview
The Bosch 31686560 (Bosch 0261520295) is a Bosch HDP5 mechanical high-pressure fuel pump for Volvo 2.0L Drive-E turbo and twin-charged engines (B4204T / T5 / T6 / T8). It is listed for the XC90 II T6 (2016-2023), XC60 II T6 (2018-2023) and S90 II T6 (2017-2023). An exhaust camshaft pump lobe drives the roller tappet to a 200 bar (20 MPa / 2900 psi) injection pressure, with a digital metering valve of 9.8-12.0 Ω at 20°C. Flange bolts are tightened in alternating diagonal steps to 13 N·m and the high-pressure pipe flare nut to 25 N·m. Common codes are P0087, P0088 and P1193. The internal roller follower should be lubricated with clean engine oil before the pump enters the cylinder head bore.
Always verify the OE reference 31478796, 31375549 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 31686560 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| System Type | Bosch HDP5 Mechanical High Pressure Fuel Pump |
| Operating PressureCore Spec | |
| Actuation Type | Exhaust camshaft dedicated pump lobe driving roller tappet |
| Mounting Flange Bolt Torque | 13 N·m (alternating diagonal progressive tightening) |
| High Pressure Pipe Torque | 25 N·m Flare Nut Connection |
| Flow Control Solenoid Resistance | 9.8 - 12.0 Ω at 20°C (ECU digital metering valve) |
| Common Fault Codes | P0087 (Fuel Rail Pressure Too Low), P0088 (Rail Pressure Too High), P1193 (Fuel Delivery Error) |
| Workshop Precaution | Lubricate internal roller follower with clean engine oil prior to inserting into cylinder head bore |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel Rail & Remove Acoustic Cover: Depressurize fuel rail via diagnostic scan tool or fuse isolation. Remove upper engine acoustic shroud to access the cylinder head rear.
- Disconnect Fuel Feed Hose & Steel High Pressure Union: Detach low pressure quick-release fuel supply hose. Unscrew high pressure steel pipe flare nut (25 N·m) with backup counter-wrench.
- Unbolt Mounting Fasteners & Inspect Roller Lifter: Loosen two M6 Torx mounting bolts evenly in half-turn increments to relieve spring tension. Remove pump and inspect camshaft roller tappet for scoring.
- Fit New O-Ring, Torque Bolts Evenly & Check For Leaks: Install replacement O-ring with fresh engine oil coating. Torque mounting bolts alternately to 13 N·m. Tighten steel line to 25 N·m. Test run engine.
- Verify fitment against the vehicle EPC using part number 31686560 and the listed cross references before ordering.
- Tighten the mounting/hold-down fasteners to 13 N·m.
- Tighten the high-pressure line to 25 N·m.
Frequently Asked Questions
Does part 31686560 fit my Volvo 2.0L Drive-E?
Part 31686560 is a gasoline direct-injection high-pressure fuel pump for Volvo 2.0L Drive-E Turbo & Twin-Charged B4204T / T5 / T6 / T8 engines. Listed fitment is XC90 II T6 AWD 2.0L B4204T27 Twincharged 235 kW (2016-2023), XC60 II T6 AWD 2.0L B4204T27 Twincharged 235 kW (2018-2023), and S90 II T6 AWD 2.0L B4204T27 Twincharged 235 kW (2017-2023). Confirm against the vehicle EPC before ordering.
What fault codes can be associated with this high-pressure fuel pump?
The listed diagnostic trouble codes are P0300, P0087, P0193, P0089, and P0191. These codes do not by themselves confirm pump failure, and the supplied facts do not define individual fault conditions. Diagnose using the vehicle EPC and repair information.
Does this pump need coding or adaptation after installation?
Coding/adaptation requirements are not stated in the supplied facts. Confirm this against the vehicle EPC before installation. The system pressure listed for this pump is 200 bar.
How can I verify that the old pump is part 31686560?
Check the old pump's part number against 31686560 and the listed cross references: 31686560, 31478796, 31375549, 0261520295, 0261520476, and 0261520215. If the marking cannot be matched, confirm fitment against the vehicle EPC before installation.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.