DENSO 31303495
High Pressure Fuel Injector Volvo XC90 XC60 S90 V60 2.0T Drive E T5 T6 31465786
31465786, 31336691, 31336692, 0261500366HIGH-SPEED ELECTROMAGNETIC MULTI-HOLE MICRO SOLENOID-200 bar peak rail pressureProduct Overview
The Denso 31303495 (Volvo 31465786) is a multi-hole laser direct gasoline injector for Volvo 2.0L Drive-E turbo and twin-charged engines (B4204T / T5 / T6 / T8). It is listed for the XC90 II (2016-2024), XC60 II (2018-2024) and S90 II (2017-2024). It runs at rail pressures up to 200 bar (20 MPa / 2900 psi) with a precision laser-drilled asymmetric spray cone targeting intake swirl; solenoid coil resistance is 1.7-2.1 Ω at 20°C. Flanged rail bracket fasteners take 11 N·m and the fuel delivery rail pipe union 25 N·m. Common codes for this fitment are P0300, P0301-P0304 and P0171. New Teflon combustion chamber seal rings must be fitted using an expansion mandrel and calibration collet.
Always verify the OE reference 31465786, 31336691, 31336692 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 31303495 needs no ECU calibration coding; no code transfer is required after fitting.
Vehicle & Engine Fitment
Technical Specifications
| Specification | Value |
|---|---|
| System Type | Denso Multi-Hole Laser Direct Gasoline Fuel Injector |
| Operating PressureCore Spec | |
| Spray Geometry | Precision laser-drilled asymmetric spray cone targeting intake swirl |
| Fuel Rail Bolt Torque | 11 N·m (flanged rail bracket fasteners) |
| High Pressure Pipe Torque | 25 N·m (fuel delivery rail pipe union) |
| Solenoid Coil Resistance | 1.7 - 2.1 Ω at 20°C (rapid actuation pulse circuit) |
| Common Fault Codes | P0300 (Random Misfire), P0301-P0304 (Cylinder Misfire), P0171 (System Lean Bank 1) |
| Workshop Precaution | Always fit new Teflon combustion chamber seal rings using expansion mandrel and calibration collet |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Depressurize Fuel System & Remove Air Filter Housing: Depressurize fuel rail via diagnostic scan tool command. Remove intake air filter ducting and upper acoustic shield.
- Disconnect Injector Harness & High Pressure Delivery Rail: Unclip wiring harness from all four injectors. Loosen high-pressure delivery pipe (25 N·m) and unbolt fuel rail retaining screws (11 N·m).
- Extract Injectors & Install Replacement Teflon Radial Seals: Withdraw direct injectors using slide puller. Clean carbon deposits from cylinder head bores. Install new Teflon seals and resize with calibration sleeve.
- Reinstall Fuel Rail Assembly & Torque Connections: Press injectors firmly into ports. Torque rail bolts evenly to 11 N·m. Tighten high pressure line union to 25 N·m. Start engine and verify zero fuel weepage.
- Confirm fitment by VIN and the vehicle's EPC before ordering or installing this injector.
- Tighten the injector hold-down to 11 N·m and the high-pressure line to 25 N·m.
- Verify the old injector part number against 31303495 and the listed cross references before replacement.
Frequently Asked Questions
Which vehicles does part number 31303495 fit, and how can I verify the old part?
Part number 31303495 is a gasoline direct-injection injector listed for the Volvo 2.0L Drive-E Turbo & Twin-Charged engine family (B4204T / T5 / T6 / T8) in XC90 II (2016-2024), XC60 II (2018-2024), and S90 II (2017-2024). Verify the old unit against part number 31303495 and the listed cross references: 31303495, 31465786, 31336691, 31336692, 0261500366, 0261500162. Confirm fitment by VIN and the vehicle's EPC before ordering or installing.
What diagnostic trouble codes are listed, and can they confirm a failed injector?
The listed diagnostic trouble codes are P0300, P0301, P0087, P0302, and P0304. These codes alone do not confirm injector failure; use the vehicle's service information for diagnosis and confirm the part against the EPC.
Does this injector require coding or adaptation, and what service life should I expect?
Coding or adaptation requirements and expected service life are not stated in the verified facts. Confirm both against the vehicle's EPC or service information instead of guessing.
Can I reuse the seals, and what torque and pressure values apply?
Seal reuse guidance is not stated in the verified facts, so confirm it against the vehicle's EPC or service information. The mounting/hold-down torque is 11 N·m, the high-pressure line torque is 25 N·m, and the system pressure is 200 bar.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.