BOSCH 13538625397
Fuel Injector BMW 1 2 3 4 Series X1 X2 Mini Cooper 1.5T B38 2.0T B48 0261500560
8625397, 13537639998, 0261500560--200 bar peak rail pressureProduct Overview
The 13538625397 is an original equipment (BOSCH) precision component engineered specifically for the BMW TwinPower Turbo 1.5L 3-Cyl (B38) & 2.0L 4-Cyl (B48) DOHC 16V HDEV5. Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0300, P0301, P0171, P0172.
Always verify the OE reference 8625397, 13537639998 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 13538625397 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 13538625397 |
| Manufacturer Brand | BOSCH |
| Component Type | Direct Fuel Injector |
| Engine Application | BMW TwinPower Turbo 1.5L 3-Cyl (B38) & 2.0L 4-Cyl (B48) DOHC 16V HDEV5 |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 13 N-m (115 lb-in) |
| Fuel Line / Rail Torque | 23 N-m (17 lb-ft) |
| Primary Diagnostic Fault Codes | P0300, P0301, P0171, P0172 |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 13 N-m (115 lb-in), and torque fuel line fittings to 23 N-m (17 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Confirm the engine family and exact application against the listed B38 / B48 / B58 fitment before installation.
- Tighten the injector hold-down to 13 N·m and the high-pressure line to 23 N·m.
- Match the old unit against the listed cross references before replacement.
Frequently Asked Questions
Will part 13538625397 fit my BMW or Toyota GR Supra?
Part 13538625397 is a gasoline direct-injection injector for the BMW B38 / B48 / B58 Modular TwinPower Turbo engine family (1.5L / 2.0L / 3.0L & TU). Listed fitment includes BMW 3 Series (G20) / 5 Series (G30) / X3 (2019-2024), Toyota GR Supra (A90) (2019-2024), BMW 3 Series (G20) / 4 Series (G22) (2019-2024), and BMW 3 Series (F30) / 2 Series (F22) (2015-2019). Confirm the exact vehicle against its EPC before ordering.
What diagnostic trouble codes are listed for this injector, and what symptoms should I check?
The verified diagnostic trouble codes are P0300, P0301, P0087, P0302, and P0304. No additional symptom details are stated in the provided facts, so confirm any further diagnosis against the vehicle’s EPC instead of guessing.
What hold-down and high-pressure line torques apply, and can I reuse the seals?
The mounting / hold-down torque is 13 N·m and the high-pressure line torque is 23 N·m for this gasoline direct-injection injector; system pressure is 200 bar. Seal reuse is not stated in the provided facts, so confirm it against the vehicle’s EPC instead of guessing.
How can I verify the old injector before replacement?
Compare the old unit with these cross references: 13538625397, 8625397, 13537639998, 0261500560, 0261520521, and 13518604229. Also confirm the exact application and any coding or adaptation requirement against the vehicle’s EPC instead of guessing.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.