BOSCH 13538656548
Fuel Injector 350 bar BMW 330i 530i M340i 540i X3 X5 B48 B58 TU 0261500642
13538656549, 8656548, 8656549, 0261500643, 0261500642--350 bar peak rail pressureProduct Overview
The 13538656548 is an original equipment (BOSCH) precision component engineered specifically for the BMW 2.0L & 3.0L TwinPower Turbo DOHC (B48TU / B58TU / B58B30O1). Operating at peak injection pressures up to 350 bar (5075 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0300, P0301, P0171, P0172.
Always verify the OE reference 13538656549, 8656548, 8656549 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 13538656548 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 13538656548 |
| Manufacturer Brand | BOSCH |
| Component Type | Direct Fuel Injector |
| Engine Application | BMW 2.0L & 3.0L TwinPower Turbo DOHC (B48TU / B58TU / B58B30O1) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 13 N-m (115 lb-in) |
| Fuel Line / Rail Torque | 23 N-m (17 lb-ft) |
| Primary Diagnostic Fault Codes | P0300, P0301, P0171, P0172 |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 13 N-m (115 lb-in), and torque fuel line fittings to 23 N-m (17 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Torque the injector mounting/hold-down to 13 N·m.
- Torque the high-pressure line to 23 N·m.
- Verify part number 13538656548 and the listed cross-references against the vehicle's EPC before ordering or installing.
Frequently Asked Questions
Will part 13538656548 fit my vehicle?
Part 13538656548 is a gasoline direct-injection injector listed for BMW B38/B48/B58 Modular TwinPower Turbo engines (1.5L / 2.0L / 3.0L & TU). Listed fitment includes BMW 3 Series G20 / 5 Series G30 / X3 2019-2024, Toyota GR Supra A90 2019-2024, BMW 3 Series G20 / 4 Series G22 2019-2024, and BMW 3 Series F30 / 2 Series F22 2015-2019. Confirm the exact vehicle application against the vehicle's EPC before ordering.
What diagnostic trouble codes are listed for this injector?
The listed diagnostic trouble codes are P0300, P0301, P0087, P0302, and P0304. Use these as diagnostic clues and confirm the actual fault before replacing the injector.
Does this injector need coding or adaptation after installation?
The verified facts do not state whether coding or adaptation is required for this injector. Confirm the requirement against the vehicle's EPC before installation instead of guessing.
Can I reuse the seals when installing this injector?
The verified facts do not state whether the seals can be reused. Confirm the seal reuse policy and any required seal part numbers against the vehicle's EPC.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.