BOSCH 13518641789
High Pressure Fuel Pump BMW M340i 540i X3 X5 B58 TU 3.0T 0261520521
8641789, 13518631642, 8631642, 0261520521INTEGRATED ELECTRONIC QUANTITY CONTROL SOLENOID VALVE-350 bar peak rail pressureProduct Overview
The Bosch 13518641789 (Bosch 0261520521) is a Bosch HDP6 350-bar mechanical plunger high-pressure fuel pump for BMW B38 / B48 / B58 modular TwinPower Turbo engines, including the TU variants. It is listed for the M340i G20 (2019-2024), 540i G30 (2019-2023) and Toyota GR Supra (2020-2024). A triple-lobe exhaust camshaft actuates the roller tappet bucket to a maximum rail delivery pressure of 350 bar (35 MPa / 5075 psi), with a fast PWM metering actuator of 8.5-10.5 Ω at 20°C. Flange bolts are tightened alternately in half-turn increments to 13 N·m and the rigid delivery pipe union to 28 N·m. Common codes are P0087, P102A and P0171. The roller tappet should be inspected for galling, and a high-pressure supply pipe with a deformed flare fitting should be replaced.
Always verify the OE reference 8641789, 13518631642, 8631642 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 13518641789 needs no ECU calibration coding; no code transfer is required after fitting.
Vehicle & Engine Fitment
Technical Specifications
| Specification | Value |
|---|---|
| System Type | Bosch HDP6 350-bar Mechanical Plunger High-Pressure Fuel Pump |
| Operating PressureCore Spec | |
| Drive Actuation | Triple-lobe exhaust camshaft actuation via roller tappet bucket |
| Mounting Flange Bolt Torque | 13 N·m (alternately tightened in half-turn increments) |
| High Pressure Line Torque | 28 N·m (rigid high-pressure delivery pipe union) |
| Quantity Control Valve ResistanceCore Spec | |
| Common Fault Codes | P0087 (Fuel Rail Pressure Low), P102A (Fuel Rail Volume Mismatch), P0171 (Lean Fuel Trim) |
| Workshop Precaution | Inspect roller tappet for surface galling; replace high-pressure fuel supply pipe if flare fitting shows deformation |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel Rail & Disconnect 12V Battery: Disable electric low-pressure in-tank pump fuse and crank until rail pressure falls below 5 bar. Disconnect battery negative terminal.
- Remove Engine Strut Braces & Acoustic Engine Cover: Remove upper strut braces over valve cover. Unclip acoustic sound suppression shield around high-pressure pump chamber.
- Unbolt High Pressure Unions & Flange Bolts Evenly: Disconnect flow metering solenoid harness. Unthread high-pressure pipe flare nut (28 N·m). Back out two flange mounting bolts evenly half-turn at a time.
- Install HPFP, Torque Mounting Bolts & Check for Leaks: Lubricate roller tappet bucket with clean engine oil. Seat pump and torque flange bolts to 13 N·m. Tighten high pressure line to 28 N·m. Verify zero leaks.
- Verify part number 13518641789 and its cross references against the vehicle's EPC before ordering.
- Tighten the pump mounting/hold-down fasteners to 13 N·m and the high-pressure line to 28 N·m.
- Confirm coding/adaptation and seal-reuse requirements in the vehicle's EPC/service information before installation.
Frequently Asked Questions
Will part number 13518641789 fit my BMW M340i, BMW 540i, or Toyota GR Supra?
It is listed for BMW M340i G20 (2019-2024), BMW 540i G30 (2019-2023), and Toyota GR Supra (2020-2024), and for the BMW B38/B48/B58 Modular TwinPower Turbo engine family (1.5L/2.0L/3.0L & TU). Confirm the exact application against the vehicle's EPC before ordering.
What fault codes or symptoms are associated with a failed high-pressure fuel pump?
The verified diagnostic trouble codes for this listing are P0300, P0087, P0193, P0089, and P0191. No additional symptom details are stated in the verified facts, so confirm the diagnosis and failed component against the vehicle's service information.
What are the mounting and high-pressure line torque specifications for this pump?
The mounting/hold-down torque is 13 N·m, and the high-pressure line torque is 28 N·m. The system pressure is 350 bar.
Does this high-pressure fuel pump require coding or adaptation, and can I reuse the seals?
No coding/adaptation procedure or seal-reuse guidance is stated in the verified facts for this part. Confirm both requirements against the vehicle's EPC/service information before installation instead of guessing.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.