BOSCH 13648625597
High Pressure Fuel Injector BMW 118i 218i 318i X1 MINI Cooper 1.5T B38 0261500494
8625597, 13647639994, 7639994, 0261500494INTEGRATED HIGH-SPEED SOLENOID MULTI-HOLE VALVE-200 bar peak rail pressureProduct Overview
The Bosch 13648625597 (Bosch 0261500494) is a compact Bosch HDEV5 direct gasoline injector for BMW B38 modular 1.5L TwinPower Turbo engines. It is listed for the BMW 118i F20 (2015-2019), X1 F48 sDrive18i (2016-2022) and MINI Cooper F56 (2014-2023). Operating pressure reaches 200 bar (20 MPa / 2900 psi), with a 6-hole asymmetrical laser spray aimed at 3-cylinder swirl chambers and a coil resistance of 1.8-2.2 Ω at 20°C. The fuel rail holding bracket bolts are listed at 13 N·m and the high-pressure pipe flare nut at 24 N·m. Diagnostic codes for this fitment include P0300, P0301-P0303 and P0171. Teflon combustion seals must be replaced using the BMW sizing die before installation.
Always verify the OE reference 8625597, 13647639994, 7639994 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 13648625597 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| System Type | Bosch HDEV5 Compact Direct Gasoline Fuel Injector |
| Operating PressureCore Spec | |
| Spray Pattern | 6-hole asymmetrical laser spray optimized for 3-cylinder swirl chambers |
| Fuel Rail Bolt Torque | 13 N·m (fastening hold-down bracket bolts) |
| High Pressure Pipe Torque | 24 N·m Flare Nut Connection |
| Coil Resistance | 1.8 - 2.2 Ω at 20°C (High performance peak-and-hold excitation) |
| Common Fault Codes | P0300 (Random Misfire), P0301-P0303 (3-Cylinder Misfire), P0171 (System Too Lean) |
| Workshop Precaution | Mandatory Teflon combustion seal replacement with BMW sizing die before installation |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Depressurize Fuel Rail & Remove Acoustic Engine Cover: Depressurize direct injection circuit via BMW ISTA service function or fuel pump fuse removal. Remove upper acoustic engine cover.
- Disconnect Injector Harness & High Pressure Fuel Hard Lines: Unclip wiring harness from the three injectors. Unscrew high pressure steel crossover pipe (24 N·m) and unbolt fuel rail fasteners (13 N·m).
- Extract Injectors & Install Replacement Teflon Rings: Carefully draw out direct injectors using slide hammer tool. Fit new Teflon combustion seals over injector tips and compress with sizing collar.
- Torque Fuel Rail Bolts & High Pressure Rail Line: Seat injectors into cylinder head ports. Torque fuel rail hold-down bolts to 13 N·m. Tighten high pressure pipe flare nut to 24 N·m. Verify zero leaks.
- Verify the old injector against cross references 13648625597, 8625597, 13647639994, 7639994, 0261500494, and 0261500109 before replacement.
- Torque the injector mounting/hold-down fastener to 13 N·m.
- Torque the high-pressure line to 24 N·m.
Frequently Asked Questions
Will this gasoline direct-injection injector fit my BMW 1 Series F20 118i or X1 F48 sDrive18i?
The listed fitment includes BMW 1 Series F20 118i 1.5L B38A15M0 Turbo 100kW (2015-2019) and BMW X1 F48 sDrive18i 1.5L B38A15A Turbo 103kW (2016-2022). It also includes Mini Cooper F56 1.5L B38A15A Turbo 100kW (2014-2023). Confirm your exact vehicle against the EPC before ordering.
What diagnostic trouble codes are listed for this injector?
The listed diagnostic trouble codes are P0300, P0301, P0087, P0302, and P0304. The supplied facts do not state specific symptoms or a diagnostic test procedure, so confirm the fault path against the vehicle's EPC instead of guessing.
Does this injector require coding or adaptation after installation?
Coding and adaptation requirements are not stated in the verified facts, so confirm them against the vehicle's EPC instead of guessing. The listing gives part number 13648625597 and 200 bar system pressure, but no coding or adaptation instruction.
Can I reuse the seals, and what torque should I use for the injector hold-down and high-pressure line?
Reuse of seals is not stated in the verified facts, so confirm it against the vehicle's EPC instead of guessing. Use 13 N·m for the injector mounting/hold-down torque and 24 N·m for the high-pressure line torque. System pressure is 200 bar.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.