BOSCH 13647597870
Direct Fuel Injector BMW 320i 328i 428i 528i X3 X5 2.0L Turbo N20 N26 0261500073
7597870, 13647639994, 7639994, 0261500073, 0261500109, 0261500247, FJ1177--200 bar peak rail pressureProduct Overview
The BOSCH 13647597870 is a factory precision fuel injection component engineered specifically for the BMW 2.0L TwinPower Turbo DOHC N20B20 / N26B20 & 3.0L N55. Manufactured to strict original equipment tolerances, it delivers precise fuel atomization and operates up to its rated pressure of 200 bar (2900 psi). Common operational failure symptoms that point directly to this assembly include: Persistent Diagnostic Trouble Codes such as P0300, P0301, P0171, P0172 stored in the ECM. Hard cold starting, erratic idle oscillations, and severe acceleration stumbling. Unburnt fuel smell in the exhaust, black tailpipe soot, or fuel dilution in the engine crankcase. Loss of high-RPM power and engine protection limp-mode activation under highway load.
Always verify the OE reference 7597870, 13647639994, 7639994, FJ1177 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 13647597870 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| sku | 13647597870 |
| brand | BOSCH |
| manufacturer_code | 0261500073 |
| pressure_rating | 200 bar (2900 psi) |
| torque_flange | 13 N-m (115 lb-in) |
| torque_line | 23 N-m (17 lb-ft) |
| engine_family | BMW 2.0L TwinPower Turbo DOHC N20B20 / N26B20 & 3.0L N55 |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Always replace single-use high-pressure fuel lines and Teflon/copper sealing washers before installation.
- Lubricate the pump roller tappet or injector O-rings with clean engine oil before guiding into place.
- Tighten mounting flange fasteners in an even criss-cross pattern to 13 N-m (115 lb-in).
- Hand-thread fuel rail fittings first, then torque high-pressure flare nuts to 23 N-m (17 lb-ft) using a calibrated crowfoot wrench.
- Cycle the low-pressure fuel pump multiple times and perform a physical leak inspection before engine ignition.
- Confirm the exact BMW application by VIN/EPC before installing part number 13647597870.
- Tighten the injector hold-down to 13 N·m and the high-pressure line to 23 N·m.
- Verify the old injector against cross references 7597870, 13647639994, 7639994, 0261500073, and 0261500109.
Frequently Asked Questions
Which BMW models and engines does part number 13647597870 fit?
Part number 13647597870 is a gasoline direct-injection injector for BMW N20/N26/N55/S55 (2.0L & 3.0L TwinPower Turbo). Listed fitment includes BMW 3 Series F30/F31 (2012-2016), 5 Series F10/F11 (2011-2017), X3 F25/X4 F26 (2011-2017), and X5 F15/X6 F16 (2014-2018). Confirm the exact application against the vehicle’s EPC before ordering.
What diagnostic trouble codes can point to a faulty injector?
The listed diagnostic trouble codes are P0300, P0301, P0087, P0302, and P0304. Use these codes with proper diagnostics and confirm the faulty injector before replacement.
What are the mounting/hold-down and high-pressure line torque specifications?
The mounting/hold-down torque is 13 N·m and the high-pressure line torque is 23 N·m. The system pressure is 200 bar.
Do I need to code or adapt this injector, and can I reuse the seals?
The provided facts do not state coding/adaptation or seal-reuse requirements. Confirm these requirements against the vehicle’s EPC before installation instead of guessing.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.