Catalog / BOSCH / 0261520134
BOSCH

BOSCH 0261520134

View Specs
SolenoidGDI High-Pressure Fuel Pump (HPFP)Euro 6

High Pressure Fuel Pump Ford 2.0L 2.3L EcoBoost Mustang Focus RS

Reference data for BOSCH 0261520134 high-pressure fuel pump · OEM EJ7Z-9350-A, EJ7E-9D376-AA, EJ7E-9D376-AB, EJ7E-9D376-AC · Application Ford 2.0L & 2.3L EcoBoost (DOHC 16V GTDI Twin-Scroll Turbo)
OE REFERENCEEJ7Z-9350-A, EJ7E-9D376-AA, EJ7E-9D376-AB, EJ7E-9D376-AC
CONTROL VALVEINTEGRATED PULSE-WIDTH MODULATED SPILL VALVE SOLENOID
NOZZLE-
EMISSIONEuro 6
WARRANTY12 Months
01

Product Overview

The Bosch 0261520134 (Ford OE EJ7Z-9350-A / EJ7E-9D376-AA) is the genuine original equipment high-pressure fuel pump for Ford 2.0L and 2.3L EcoBoost turbocharged engines. Driven by a dedicated camshaft lobe via a roller follower, this Bosch HDP-5 compact single-piston pump generates up to 200 bar (2900 psi) rail pressure. Commonly installed on the Ford Mustang 2.3L EcoBoost, Focus RS, and Explorer, it features an integrated electronic spill control valve. Typical failure signs include extended cold start crank times, hesitation above 4500 RPM, and DTC P0087.

Before You Order

HIGH-RPM FUEL CUT & ROLLER TAPPET INSPECTION: On tuned or high-boost Ford 2.3L EcoBoost engines (Mustang and Focus RS), high-pressure rail pressure collapse under full load drops fuel delivery below 50 bar, triggering sudden boost cut, misfire DTC P0300, and lean condition P0171. Inspect the camshaft roller tappet (Ford OE AG9Z-6C535-A) for scoring; never install a new pump without lubricating the plunger shaft and verifying roller rotation.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Ford Mustang 2.3 EcoBoostFord 2.0L & 2.3L EcoBoost (DOHC 16V GTDI Twin-Scroll Turbo)2015-2023
Ford Focus RSFord 2.0L & 2.3L EcoBoost (DOHC 16V GTDI Twin-Scroll Turbo)2016-2018
Ford Explorer 2.3Ford 2.0L & 2.3L EcoBoost (DOHC 16V GTDI Twin-Scroll Turbo)2016-2023
04

Technical Specifications

SpecificationValue
Pump GenerationBosch HDP-5 Radial-Piston High-Pressure Fuel Pump
Operating Rail PressureCore Spec
Cam Drive TypeExhaust Camshaft Lobe via Roller Follower (Ford AG9Z-6C535-A)
Flow Regulation ControlIntegrated Pulse-Width Modulated Spill Valve Solenoid
Pump Flange Mounting Torque13 N·m (Even cross-pattern)
High Pressure Pipe Flare Nut Torque32 N·m
Tightening Torque32 N·m
Primary OEM ReferenceEJ7Z-9350-A, EJ7E-9D376-AA, EJ7E-9D376-AB
Engine Emission ComplianceEuro 6 / LEV III / Tier 3 Bin 30
Standard Industrial Warranty12 Months / Unlimited Mileage

Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)

Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.

BOSCHExact Engine & Chassis Match
0261500298
Gasoline Direct Injection (GDI) • 200 bar
🚙 Ford Explorer 2.3 (FORD 2.0L & 2.3L ECOBOOST)
Technical Specifications & Pinout
BOSCHExact Engine & Chassis Match
BB5Z-9F593-B
Gasoline Direct Injection (GDI) • 150 bar
🚙 Ford Explorer 2.3 (FORD 2.0L & 2.3L ECOBOOST)
Technical Specifications & Pinout
BOSCHExact Engine & Chassis Match
EJ7E-9F593-AA
Gasoline Direct Injection (GDI) • 200 bar
🚙 Ford Mustang 2.3 Ecoboost (FORD 2.0L & 2.3L ECOBOOST)
Technical Specifications & Pinout
BOSCHExact Engine & Chassis Match
EJ7Z-9F593-A
Gasoline Direct Injection (GDI) • 200 bar
🚙 Ford Mustang 2.3 Ecoboost (FORD 2.0L & 2.3L ECOBOOST)
Technical Specifications & Pinout
05

Installation Tips

Tools needed: Line flare wrench for high-pressure fuel rail pipe nut, 8mm and 10mm sockets with ratchet and extension, Torque wrench calibrated for 10-35 N·m, Clean engine oil or assembly lubricant for roller follower and seal, Eye protection and absorbent rags for high-pressure fuel relief

  1. Disconnect battery negative terminal; remove fuel pump fuse and crank engine to bleed static fuel pressure.
  2. Wrap clean cloth around high-pressure fuel line fitting; loosen flare nut gradually to relieve remaining pressure.
  3. Disconnect electrical connector from HPFP volume control solenoid.
  4. Disconnect low-pressure fuel supply line quick-connect coupler.
  5. Loosen the two pump mounting bolts evenly half-turn by half-turn to relieve cam spring load smoothly.
  6. Remove pump assembly; extract roller follower AG9Z-6C535-A and inspect for flat spots or needle bearing play.
  7. Clean cylinder head mating surface; lubricate new pump Viton O-ring with fresh engine oil.
  8. Rotate engine until camshaft driving lobe is on base circle (lowest lift point).
  9. Install lubricated roller follower into bore; seat pump body square against cylinder head.
  10. Torque mounting bolts alternately in progressive steps to 13 N·m.
  11. Thread high-pressure steel line flare nut hand-tight; torque to 32 N·m.
  12. Reconnect low-pressure fuel hose and electrical plug; cycle ignition 3 times and check for leaks.
Tips & Warnings:
  • Counter-Holding Pipe Nut: Always counter-hold the pump body outlet fitting when tightening the high-pressure steel line flare nut to prevent fitting damage.
  • Base Circle Positioning: Rotate engine to lowest camshaft lobe position before installing pump to avoid stripping aluminum head threads.
  • Roller Follower Renewal: Replace the roller follower during every pump renewal to ensure smooth operation and prevent warranty voiding.
06

Frequently Asked Questions

QWhat are the common symptoms of a failing 0261520134 pump on a Focus RS or Mustang EcoBoost?

Symptoms include violent engine bucking or fuel cut on wide-open throttle (WOT) above 4,000 RPM, long cold cranking times of 4 to 6 seconds, and diagnostic trouble codes P0087 (Fuel Rail Pressure Too Low) and P0088.

QWhat is the tightening torque for the Ford 2.3 EcoBoost HPFP bolts?

Torque the two mounting bolts evenly to 13 N·m (115 lb-in). The high-pressure stainless steel fuel delivery line nut must be torqued to 32 N·m (24 lb-ft). Always replace the high-pressure steel hardline after disassembly.

QDo I need to replace the roller follower when installing a new pump?

Yes, highly recommended. The roller follower (AG9Z-6C535-A) experiences high cyclic contact fatigue. If the needle bearings inside the roller fail or the outer surface shows flat spots, it will rapidly destroy the new pump plunger.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0088Critical

Fuel Rail/System Pressure Too High

P0089Critical

Fuel Pressure Regulator 1 Performance

P0191Critical

Fuel Rail Pressure Sensor 'A' Circuit Range/Performance

P0002High

Fuel Volume Regulator Control Circuit Range / Performance (VCV / IMV)

P0090High

Fuel Pressure Regulator 1 Control Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

COMMON RAIL WORKSHOP DIAGNOSTICS

Common Rail High-Pressure Pump Diagnostics Guide

Diagnose common rail high-pressure pump failure: suction vacuum, CP4 roller glitter, plunger wear, air ingress & P0087 hard start. Workshop bench testing.

Read Technical Protocol
COMMON RAIL WORKSHOP DIAGNOSTICS

Fuel Metering Valve (IMV/SCV) Diagnostics Guide

Diagnostic guide for common rail fuel metering valves (IMV/SCV/FCA/MPROP). Normally open vs closed, coil resistance, PWM duty cycle & P0088 / P0089 test.

Read Technical Protocol
OBD-II DIAGNOSTIC PROTOCOL

P0087 Low Rail Pressure Diagnosis Guide

Step-by-step workshop diagnostic protocol for OBD-II DTC P0087 (Fuel Rail Pressure Too Low). 5-stage troubleshooting tree: backleak testing, SCV valve, PRV valve, and high-pressure pump.

Read Technical Protocol
COMMON RAIL WORKSHOP DIAGNOSTICS

Rail Pressure Relief Valve Diagnostics Guide

Common rail pressure relief valve (PRV) testing guide. Diagnose hot start stalls, P0087 rail pressure loss, return line leakage & single vs 2-stage valves.

Read Technical Protocol