BOSCH EJ7Z-9F593-A
High Pressure Fuel Injector Ford Mustang Focus RS Explorer 2.3 EcoBoost 0261500203
EJ7G-9F593-AA, 0261500203, 0261500204MULTI-HOLE LASER DRILLED SOLENOID ACTUATED NOZZLE-200 bar peak rail pressureProduct Overview
The Bosch EJ7Z-9F593-A (Bosch 0261500203) is a Bosch HDEV5 multi-hole solenoid direct gasoline injector for Ford's 2.0L and 2.3L EcoBoost DOHC 16V GTDI twin-scroll turbo engines. The fitment list covers the Mustang 2.3 EcoBoost (2015-2023), Focus RS (2016-2018) and Explorer 2.3 EcoBoost (2016-2023). It operates at rail pressures up to 200 bar (20 MPa / 2900 psi) and meters fuel through a 6-hole laser-drilled asymmetrical spray pattern matched to tumble charge air. Workshop figures give 21 N·m for the fuel rail holding bracket bolts and 25 N·m for the high-pressure pipe flare nut; coil resistance is 1.4-1.8 Ω at 20°C. Common diagnostic codes for this fitment are P0300, P0301-P0304 and P0171. The combustion chamber Teflon seals are single-use: discard the old seals and fit a new blue Teflon seal kit with an expanding mandrel.
Always verify the OE reference EJ7G9F593AA stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. EJ7Z-9F593-A needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| System Type | Bosch HDEV5 Multi-Hole Solenoid Direct Gasoline Fuel Injector |
| Operating PressureCore Spec | |
| Spray Pattern | 6-hole laser-drilled asymmetrical pattern for tumble charge air |
| Fuel Rail Bolt Torque | 21 N·m (holding bracket bolts) |
| High Pressure Pipe Torque | 25 N·m Flare Nut Connection |
| Coil Resistance | 1.4 - 1.8 Ω at 20°C (High performance peak-and-hold circuit) |
| Common Fault Codes | P0300 (Random Misfire), P0301-P0304 (Cylinder Misfire), P0171 (System Lean Under Boost) |
| Workshop Precaution | Discard existing combustion chamber Teflon seals; install new blue Teflon seal kit with expanding mandrel |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Relieve Residual Fuel Pressure & Remove Intake Pleno: Depressurize high pressure fuel rail via diagnostic scan tool or fuel pump fuse isolation. Remove upper engine cover and sound dampener.
- Disconnect Fuel Rail Wiring & Fuel Lines: Unclip direct injector wiring harnesses. Unscrew fuel rail cross-over pipe flare nuts (25 N·m) and rail retaining bolts (21 N·m).
- Extract Injector Assembly & Fit Teflon Seals: Use slide hammer injector puller tool to lift injectors vertically. Fit new Teflon tip seal and compress with sizing die.
- Torque Rail Bracket & Test For Leaks: Seat injectors into cylinder ports. Torque rail bolts to 21 N·m. Tighten fuel pipe to 25 N·m. Prime fuel system and check for odor or seepage.
- Verify EJ7Z-9F593-A and the vehicle application against the EPC before installation.
- Tighten the injector mounting/hold-down to 21 N·m.
- Tighten the high-pressure line to 25 N·m.
Frequently Asked Questions
Which vehicles does EJ7Z-9F593-A fit?
The listed fitment is Ford Mustang 2.3 EcoBoost 2.3L Twin-Scroll 231kW (2015-2023), Ford Focus RS 2.3 AWD 2.3L EcoBoost 257kW (2016-2018), and Ford Explorer 2.3 EcoBoost 2.3L Turbo 206kW (2016-2023). It belongs to the Ford 2.0L & 2.3L EcoBoost DOHC 16V GTDI Twin-Scroll Turbo engine family. Confirm any other application against the vehicle’s EPC.
What fault codes can indicate a problem with this injector?
The listed diagnostic trouble codes are P0300, P0301, P0087, P0302, and P0304. Use these codes with vehicle-specific diagnostics; no other symptom or code is stated in the verified facts.
Does this injector require coding or adaptation after installation?
No coding or adaptation requirement is stated in the verified facts for this injector. Confirm any required coding or adaptation against the vehicle’s EPC/service information before installation.
How can I verify the old injector part number?
Compare the old injector marking with EJ7Z-9F593-A and the listed cross references: EJ7Z9F593A, EJ7G9F593AA, 0261500203, 0261500204, 0261500109, CM5E9F593BB. If it does not match, confirm fitment against the vehicle’s EPC before ordering.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.