Catalog / BOSCH / BB5Z-9F593-B
BOSCH

BOSCH BB5Z-9F593-B

View Specs
SolenoidGasoline Direct Injection (GDI / HDEV)Euro 6

Direct Fuel Injector Ford Explorer Edge Escape Fusion Focus ST 2.0L EcoBoost 0261500155

Reference data for BOSCH BB5Z-9F593-B common rail injector · OEM BB5E-9F593-BA, CM5213, FJ1116, 0261500156, 0261500155 · Application Ford 2.0L & 2.3L EcoBoost (DOHC 16V GTDI Twin-Scroll Turbo)
OE REFERENCEBB5E-9F593-BA, CM5213, FJ1116, 0261500156, 0261500155
CONTROL VALVE-
NOZZLE-
EMISSIONEuro 6
WARRANTY12 Months
01

Product Overview

The BB5Z-9F593-B is an original equipment (BOSCH) precision component engineered specifically for the Ford 2.0L EcoBoost Turbocharged DOHC 16V I4. Operating at peak injection pressures up to 150 bar (2175 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0300, P0301, P0172, P0087.

Before You Order

Always verify the OE reference BB5E9F593BA, CM5213, FJ1116 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. BB5Z-9F593-B needs no ECU calibration coding; no code transfer is required after fitting.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Ford Mustang 2.3 EcoBoostFord 2.0L & 2.3L EcoBoost (DOHC 16V GTDI Twin-Scroll Turbo)2015-2023
Ford Focus RSFord 2.0L & 2.3L EcoBoost (DOHC 16V GTDI Twin-Scroll Turbo)2016-2018
Ford Explorer 2.3Ford 2.0L & 2.3L EcoBoost (DOHC 16V GTDI Twin-Scroll Turbo)2016-2023
04

Technical Specifications

SpecificationValue
Part Number / SKUBB5Z-9F593-B
Manufacturer BrandBOSCH
Component TypeDirect Fuel Injector
Engine ApplicationFord 2.0L EcoBoost Turbocharged DOHC 16V I4
Operating PressureCore Spec
Mounting Torque (Flange / Bracket)10 N-m (89 lb-in)
Fuel Line / Rail Torque20 N-m (15 lb-ft)
Primary Diagnostic Fault CodesP0300, P0301, P0172, P0087

Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)

Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.

BOSCHExact Engine & Chassis Match
0261520134
Gasoline Direct Injection (GDI) • 200 bar
🚙 Ford Explorer 2.3 (FORD 2.0L & 2.3L ECOBOOST)
Technical Specifications & Pinout
BOSCHExact Engine & Chassis Match
AG9Z-9350-B
Gasoline Direct Injection (GDI) • 150 bar
🚙 Ford Explorer 2.3 (FORD 2.0L & 2.3L ECOBOOST)
Technical Specifications & Pinout
BOSCHExact Engine & Chassis Match
BB5Z-9350-A
Gasoline Direct Injection (GDI) • 200 bar
🚙 Ford Explorer 2.3 (FORD 2.0L & 2.3L ECOBOOST)
Technical Specifications & Pinout
BOSCHExact Engine & Chassis Match
0261520152
Gasoline Direct Injection (GDI) • 200 bar
🚙 Engine Code FORD 2.0L & 2.3L ECOBOOST
Technical Specifications & Pinout
BOSCHExact Engine & Chassis Match
CJ5Z-9350-B
Gasoline Direct Injection (GDI) • 150 bar
🚙 Engine Code FORD 2.0L & 2.3L ECOBOOST
Technical Specifications & Pinout
05

Installation Tips

  1. Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
  2. Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
  3. Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
  4. Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 10 N-m (89 lb-in), and torque fuel line fittings to 20 N-m (15 lb-ft).
  5. Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
Tips & Warnings:
  • Always verify the exact Ford EcoBoost application against the EPC before fitting BB5Z-9F593-B.
  • Because coding and adaptation requirements are not stated, confirm them in the workshop manual before starting the job.
  • Use the vehicle's workshop data for installation specifications rather than relying on general assumptions.
06

Frequently Asked Questions

QWill BB5Z-9F593-B fit my Ford EcoBoost vehicle?

BB5Z-9F593-B is listed for Ford Mustang, Focus RS, and Explorer applications in the Ford EcoBoost engine family shown; confirm your exact vehicle against the EPC before ordering.

QWhat should I check before ordering this injector?

Confirm the vehicle's exact application against the EPC and workshop data, then verify that BB5Z-9F593-B is the correct listed injector for that Ford EcoBoost fitment.

QWhat are the symptoms of a failed unit?

The supplied product data does not list failure symptoms, so use the vehicle's workshop diagnostics to confirm whether the injector is faulty before replacement.

QDoes the old injector need to be matched or adapted?

Coding or adaptation requirements are not stated in the supplied data; confirm whether matching or adaptation is required using the vehicle's EPC or workshop manual.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0200Critical

Fuel Injector Circuit Malfunction (General / Common Driver Stage)

P0201Critical

Injector Circuit Malfunction - Cylinder 1

P0300Critical

Random or Multiple Cylinder Misfire Detected

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

COMMON RAIL WORKSHOP DIAGNOSTICS

Fuel Metering Valve (IMV/SCV) Diagnostics Guide

Diagnostic guide for common rail fuel metering valves (IMV/SCV/FCA/MPROP). Normally open vs closed, coil resistance, PWM duty cycle & P0088 / P0089 test.

Read Technical Protocol
OBD-II DIAGNOSTIC PROTOCOL

P0087 Low Rail Pressure Diagnosis Guide

Step-by-step workshop diagnostic protocol for OBD-II DTC P0087 (Fuel Rail Pressure Too Low). 5-stage troubleshooting tree: backleak testing, SCV valve, PRV valve, and high-pressure pump.

Read Technical Protocol
DIESEL WORKSHOP DIAGNOSTIC SOP

Cylinder Balance & Injector Deviation Guide

Common rail diesel cylinder balance & smooth running diagnostic guide. Balance rates, mg/stroke deviation, P0263 misfire, compression vs injector test.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol