Catalog / BOSCH / 0261520215
BOSCH

BOSCH 0261520215

View Specs
SolenoidGDI High-Pressure Fuel Pump (HPFP)Euro 6

High Pressure Fuel Pump Mercedes Benz C250 E250 SLK250 M271 EVO CGI

Reference data for BOSCH 0261520215 high-pressure fuel pump · OEM A2710702201, 2710702201, A2710703501, 2710703501, A2710703701, 2710703701, 0261520216 · Application Mercedes-Benz M271 EVO (1.8L CGI Turbo M271.820 / M271.860)
OE REFERENCEA2710702201, 2710702201, A2710703501, 2710703501, A2710703701, 2710703701, 0261520216
CONTROL VALVEINTEGRATED PULSE-WIDTH MODULATED ELECTRIC SPILL VALVE (SCV)
NOZZLE-
EMISSIONEuro 6
WARRANTY12 Months
01

Product Overview

The 0261520215 is an industrial-grade genuine Tier-1 replacement engineered for Mercedes-Benz 1.8L M271 EVO CGI Turbo (M271.820, M271.860, M271.861). Designed for high-precision Mercedes-Benz CGI Stratified Charged Gasoline Injection, it delivers factory calibration standards, OE cross-reference compatibility, and verified workshop reliability.

Before You Order

Always verify the OE reference A2710702201, 2710702201, A2710703501, 2710703501 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 0261520215 needs no ECU calibration coding; no code transfer is required after fitting.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Mercedes-Benz C-Class W204 C250 CGIMercedes-Benz M271 EVO (1.8L CGI Turbo M271.820 / M271.860)2009-2014
Mercedes-Benz E-Class W212 E250 CGIMercedes-Benz M271 EVO (1.8L CGI Turbo M271.820 / M271.860)2009-2016
Mercedes-Benz SLK-Class R172 SLK250Mercedes-Benz M271 EVO (1.8L CGI Turbo M271.820 / M271.860)2011-2016
04

Technical Specifications

SpecificationValue
System TypeBosch HDP-5 Mechanical Direct Injection High Pressure Pump
Operating PressureCore Spec
Actuation MechanismExhaust Camshaft Twin-Lobe Mechanical Driven
Mounting Flange Torque12 N·m M6 Fasteners
High Pressure Line Torque28 N·m Flare Nut
Control ValveCore Spec
Common Fault CodesP0087 (Rail Pressure Low), P0171 (System Lean Bank 1), P0172 (Fuel Dilution Rich)
Workshop PrecautionInspect engine oil smell and level before replacing to prevent bearing damage from fuel dilution
05

Installation Tips

  1. Depressurize Fuel Rail & Isolate High-Pressure Circuit: Pull fuel pump relay in rear fuse box and crank engine for 10 seconds. Verify scan tool low pressure fuel reading falls under 5 bar before cracking flare nuts.
  2. Inspect Engine Oil for Fuel Dilution: Pull oil dipstick. If oil level is elevated or smells strongly of gasoline due to internal plunger seal blowby, schedule immediate oil and filter change.
  3. Clean Cylinder Head Bore & Lubricate O-Ring: Clean mounting bore on cylinder head. Coat new Viton O-ring with clean engine oil. Never use silicone sealant on flange face.
  4. Torque Flange Fasteners Alternately: Position pump on cylinder head while camshaft is at base circle. Thread mounting bolts hand-tight, then torque alternately to 12 N·m.
  5. Connect High-Pressure Hard Line & Torque: Align high-pressure hard line square into pump discharge port. Finger-tighten fitting, then secure flare nut to exactly 28 N·m.
Tips & Warnings:
  • Cross-check part number 0261520215 against A2710702201, 2710702201, A2710703501, 2710703501, and A2710703701 before fitting.
  • Tighten the high-pressure common-rail fuel pump mounting/hold-down fasteners to 12 N·m.
  • Tighten the high-pressure line to 28 N·m.
06

Frequently Asked Questions

QWhy does engine oil smell like gasoline on Mercedes M271 EVO engines?

The high-pressure plunger seal in the Bosch 0261520215 pump wears over time. Under 140 bar pressure, atomized fuel bypasses the internal shaft seal directly down into the cylinder head and engine oil pan, causing crankcase fuel dilution and raising oil levels.

QWhat diagnostic trouble codes occur when this pump fails?

Typical codes are P0087 (Fuel Rail/System Pressure Too Low under acceleration), P0171 (System Too Lean), or P0172 caused by excessive gasoline fumes from the crankcase ventilation system.

QWhat are the exact tightening torques for installation?

Flange mounting bolts must be torqued alternately to 12 N·m. The high-pressure pipe flare nut requires exactly 28 N·m.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0088Critical

Fuel Rail/System Pressure Too High

P0089Critical

Fuel Pressure Regulator 1 Performance

P0191Critical

Fuel Rail Pressure Sensor 'A' Circuit Range/Performance

P0002High

Fuel Volume Regulator Control Circuit Range / Performance (VCV / IMV)

P0090High

Fuel Pressure Regulator 1 Control Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

COMMON RAIL WORKSHOP DIAGNOSTICS

Common Rail High-Pressure Pump Diagnostics Guide

Diagnose common rail high-pressure pump failure: suction vacuum, CP4 roller glitter, plunger wear, air ingress & P0087 hard start. Workshop bench testing.

Read Technical Protocol
COMMON RAIL WORKSHOP DIAGNOSTICS

Fuel Metering Valve (IMV/SCV) Diagnostics Guide

Diagnostic guide for common rail fuel metering valves (IMV/SCV/FCA/MPROP). Normally open vs closed, coil resistance, PWM duty cycle & P0088 / P0089 test.

Read Technical Protocol
OBD-II DIAGNOSTIC PROTOCOL

P0087 Low Rail Pressure Diagnosis Guide

Step-by-step workshop diagnostic protocol for OBD-II DTC P0087 (Fuel Rail Pressure Too Low). 5-stage troubleshooting tree: backleak testing, SCV valve, PRV valve, and high-pressure pump.

Read Technical Protocol
COMMON RAIL WORKSHOP DIAGNOSTICS

Rail Pressure Relief Valve Diagnostics Guide

Common rail pressure relief valve (PRV) testing guide. Diagnose hot start stalls, P0087 rail pressure loss, return line leakage & single vs 2-stage valves.

Read Technical Protocol