BOSCH A2740700501
High Pressure Fuel Pump Mercedes Benz C300 E300 GLC300 2.0T M274 0261520215
2740700501, A2740700401, 0261520215, 0261520216INTEGRATED SOLENOID QUANTITY CONTROL VALVE (FLOW METERING)-200 bar peak rail pressureProduct Overview
The Bosch A2740700501 (Bosch 0261520215) is a camshaft-driven single-piston high-pressure fuel pump for Mercedes-Benz M270 and M274 1.6L / 2.0L BlueDIRECT turbo engines. It is listed for the C300 W205 (2015-2021), E300 W213 (2017-2020) and GLC300 X253 (2016-2020). A three-lobe exhaust camshaft actuates the roller tappet bucket to produce 200 bar (20 MPa / 2900 psi), with an electronic quantity control solenoid of 8.5-10.5 Ω at 20°C. Flange mounting bolts are tightened evenly in a cross-pattern to 12 N·m and the high-pressure steel flare nut to 27 N·m. Common codes are P0087, P0088 and P0016. Inspect the roller tappet for wear and check the engine oil for a gasoline dilution odour before installation.
Always verify the OE reference 2740700501, A2740700401 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. A2740700501 needs no ECU calibration coding; no code transfer is required after fitting.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Mercedes-Benz C300 W205 | Mercedes-Benz M270 / M274 (1.6L & 2.0L BlueDIRECT Turbo) | 2015-2021 |
| Mercedes-Benz E300 W213 | Mercedes-Benz M270 / M274 (1.6L & 2.0L BlueDIRECT Turbo) | 2017-2020 |
| Mercedes-Benz GLC300 X253 | Mercedes-Benz M270 / M274 (1.6L & 2.0L BlueDIRECT Turbo) | 2016-2020 |
Technical Specifications
| Specification | Value |
|---|---|
| System Type | Camshaft-Driven Single-Piston High-Pressure Fuel Pump (HPFP) |
| Operating PressureCore Spec | |
| Drive Mechanism | Three-lobe exhaust camshaft actuation with roller tappet bucket |
| Flange Mounting Bolt Torque | 12 N·m (tighten evenly in cross-pattern to prevent housing tilt) |
| High Pressure Line Torque | 27 N·m (high pressure steel flare nut connection) |
| Flow Control Valve ResistanceCore Spec | |
| Common Fault Codes | P0087 (Fuel Rail Pressure Too Low), P0088 (Fuel Rail Pressure Too High), P0016 (Camshaft Correlation) |
| Workshop Precaution | Inspect roller tappet for wear prior to installation; check engine oil for gasoline dilution odor |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Relieve Fuel Line Residual Pressure & Disconnect Battery: Disconnect negative battery lead. De-pressurize low-pressure fuel circuit and cover HPFP with shop towels to catch fuel discharge during line disconnection.
- Remove Acoustic Cover & Detach Fuel Flow Control Plug: Unclip sound deadening foam around pump housing. Disconnect electrical connector from integrated fuel volume metering solenoid.
- Inspect Camshaft Roller Tappet & Fit New Viton O-Ring: Evenly loosen dual flange mounting bolts half-turn at a time. Withdraw HPFP and remove roller tappet. Inspect tappet surface for scuffing and lubricate with fresh engine oil.
- Install HPFP, Torque Mounting Bolts & Reconnect Lines: Position HPFP onto cylinder head. Alternately tighten mounting bolts to 12 N·m. Torque high pressure outlet flare nut to 27 N·m. Start engine and verify zero fuel weepage.
- Confirm part number A2740700501 and the listed cross references against the vehicle’s EPC before ordering.
- Tighten the mounting/hold-down fasteners to 12 N·m.
- Tighten the high-pressure line to 27 N·m.
Frequently Asked Questions
Will this high-pressure fuel pump fit my Mercedes-Benz C300, E300, or GLC300?
It is listed for Mercedes-Benz C300 W205 (2015–2021), E300 W213 (2017–2020), and GLC300 X253 (2016–2020) with the M270/M274 1.6L & 2.0L BlueDIRECT Turbo engine family. The part number is A2740700501, with listed cross references A2740700501, 2740700501, A2740700401, 0261520215, 0261520216, and 0261520288. Confirm fitment against the vehicle’s EPC before ordering.
What pressure and torque specs should I use for installation?
The listed system pressure is 200 bar. The mounting/hold-down torque is 12 N·m, and the high-pressure line torque is 27 N·m. Confirm any additional installation requirements against the vehicle’s EPC.
What DTCs can indicate a problem with this high-pressure fuel pump?
The listed diagnostic trouble codes are P0300, P0087, P0193, P0089, and P0191. No symptom list is included in the provided facts; use the listed DTCs as diagnostic inputs and confirm against the vehicle’s EPC.
Does this high-pressure fuel pump require coding or adaptation after installation?
No coding or adaptation requirement is stated in the listed facts. Confirm any programming or adaptation requirements against the vehicle’s EPC before installation.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.