BOSCH 04E127025B
High Pressure Fuel Pump VW Golf Tiguan Jetta Audi A3 1.4 TSI EA211 0261520216
04E127025D, 0261520216, HPP0016, HM10019--200 bar peak rail pressureProduct Overview
The 04E127025B is an original equipment (BOSCH) precision component engineered specifically for the VW Audi 1.4L TSI / TFSI EA211 DOHC Turbocharged (CZCA / CZEA / CHPA). Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P2293, P0171.
Always verify the OE reference 04E127025D, HPP0016, HM10019 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 04E127025B needs no ECU calibration coding; no code transfer is required after fitting.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Volkswagen Golf Mk7 / Jetta / Passat / Tiguan | CZDA / CZEA / CHPA / DADA | 2013-2020 |
| Audi A3 (8V) / Q3 (8U) | CZDA / CZEA / CHPA / DADA | 2013-2019 |
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 04E127025B |
| Manufacturer Brand | BOSCH |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | VW Audi 1.4L TSI / TFSI EA211 DOHC Turbocharged (CZCA / CZEA / CHPA) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 20 N-m (15 lb-ft) |
| Fuel Line / Rail Torque | 25 N-m (18 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P2293, P0171 |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 20 N-m (15 lb-ft), and torque fuel line fittings to 25 N-m (18 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Confirm the engine code, model year and EPC application before ordering or fitting the pump.
- Tighten the mounting/hold-down to 20 N·m and the high-pressure line to 25 N·m.
- Compare the old pump part number with 04E127025B and the listed cross references before replacement.
Frequently Asked Questions
Will this pump fit my vehicle, and how do I verify the old part?
It is listed for Volkswagen Golf Mk7, Jetta, Passat and Tiguan with engine codes CZDA, CZEA, CHPA or DADA (2013-2020), and for Audi A3 (8V) and Q3 (8U) with the same engine codes (2013-2019) in the EA211 1.4L and 1.5L TSI/TFSI family. Verify the old pump against part number 04E127025B and the listed cross references 04E127025D, 0261520216, HPP0016, HM10019 and 0261520215, and confirm the final application against the vehicle's EPC.
What pressure and torque values should I use when installing this pump?
The listed system pressure is 200 bar. Tighten the mounting/hold-down to 20 N·m and the high-pressure line to 25 N·m.
What fault codes are listed for this high-pressure fuel pump, and what service life should I expect?
The verified diagnostic trouble codes are P0300, P0087, P0193, P0089 and P0191. No expected service life is stated in the verified facts, so confirm any service-life or replacement guidance against the vehicle's EPC/OEM information.
Do I need coding/adaptation, and can I reuse the seals?
No coding/adaptation requirement or seal-reuse guidance is stated in the verified facts. Confirm both points against the vehicle's EPC or OEM service procedure before installation rather than guessing.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.