Catalog / BOSCH / 0445110276
BOSCH

BOSCH 0445110276

View Specs
SolenoidCommon Rail Diesel SystemEuro 4

Common Rail Injector for Common Rail Diesel

Reference data for BOSCH 0445110276 common rail injector · OEM 55200259, 93189952, 15710-79J50 · Application Z19DT / Z19DTH / 937A5 / 939A2 (1.9 CDTI / 1.9 JTD)
OE REFERENCE55200259, 93189952, 15710-79J50
CONTROL VALVEF00VC01344
NOZZLEDLLA142P1607
EMISSIONEuro 4
WARRANTY12 Months
01

Product Overview

WORKSHOP NOTICEECU Calibration / IMA Coding Required

This injector requires 6-8 digit calibration code programming (IMA / QR code) into the vehicle ECU (using Bosch KTS, Lexia/Diagbox or equivalent diagnostic equipment) following replacement to balance cylinder fuel delivery and prevent DTC P0300 misfire codes.

The Bosch 0445110276 is a second-generation Common Rail Solenoid Injector (CRI) engineered for passenger car and light commercial diesel platforms operating at peak hydraulic pressures up to 1600 bar. Driven by an ultra-fast electromagnetic actuator, this unit executes micro-second multi-pulse injection events—including pilot, pre-, main, and post-injection cycles—to optimize in-cylinder thermal rate of rise and acoustic output. Integrating the precision-ground F00VC01344 control valve and 0433171981 nozzle assembly, it achieves strict stoichiometric and particulate matter compliance under Euro 4 emission standards.

Before You Order

Technicians must cross-verify the 10-digit Bosch SKU 0445110276 and OE numbers (55200259, 93189952, or 15710-79J50) on the build plate, and register the individual alphanumeric IMA calibration code into the engine control unit before cranking.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
OE Nozzle
03

Vehicle & Engine Fitment

VehicleEngineYears
Opel Astra HZ19DT / Z19DTH / 937A5 / 939A22004-2010
Opel Vectra C / SignumZ19DT / Z19DTH / 937A5 / 939A22004-2008
Opel Zafira BZ19DT / Z19DTH / 937A5 / 939A22005-2010
Fiat Croma (194)Z19DT / Z19DTH / 937A5 / 939A22005-2011
Fiat SediciZ19DT / Z19DTH / 937A5 / 939A22006-2014
Alfa Romeo 159 1.9 JTDMZ19DT / Z19DTH / 937A5 / 939A22005-2011
Suzuki Grand Vitara II (JT)Z19DT / Z19DTH / 937A5 / 939A22005-2015
04

Technical Specifications

SpecificationValue
SKU0445110276
BrandBOSCH
Product TypeComplete Solenoid Common Rail Injector Assembly
Control ValveCore Spec
🔗 Shared Valve (2 assemblies):0445110244
Nozzle CodeCore Spec
Engine Family1.9 CDTI / 1.9 JTD (Z19DT / Z19DTH / 937A5.000 / 939A2.000)
Operating PressureCore Spec
Emission StandardEuro 4
Magnet AssemblyF00VC30319
Seal Ring KitF00VC99002
05

Installation Tips

  1. Always employ a two-wrench counter-hold technique during high-pressure pipe connection: place an open-end 14 mm wrench firmly on the injector fuel inlet body flat while torquing the fuel rail feed pipe union nut to 25–28 N·m with a calibrated flare nut wrench, preventing catastrophic internal valve spindle shear and housing distortion.
  2. Thoroughly ream and vacuum the cylinder head injector bore down to bare metal, install a new copper seal ring from seal kit F00VC99002, and apply a thin film of high-temperature non-metallic ceramic anti-seize paste strictly to the injector body shaft—never applying lubricant to the 0433171981 nozzle tip or sealing washer seat.
  3. Program the specific alphanumeric Bosch IMA trim code into the vehicle ECU diagnostic module to synchronize multi-injection volume correction, then manually prime the low-pressure fuel circuit and bleed rail air before engine cranking to prevent high-pressure dry friction galling.
Tips & Warnings:
  • Verify fitment against the listed Z19DT/Z19DTH/937A5/939A2 applications before fitting the 0445110276 injector.
  • Tighten the injector hold-down and high-pressure line to 25-30 N·m.
  • Check the 1600 bar system pressure rating and P0300/P0301/P0302/P0304/P0087 codes, and confirm any unlisted specification against the vehicle's EPC.
06

Frequently Asked Questions

QWhat is the OE cross-reference for this injector?

This injector cross-references to Fiat/Alfa Romeo part number 55200259, GM/Opel/Vauxhall part number 93189952, and Suzuki part number 15710-79J50. Technicians must visually cross-reference the stamped OE number or the Bosch production SKU 0445110276 on the injector body prior to installation.

QWhat control valve / actuator is used?

The injector utilizes the Bosch hydraulic control valve assembly part number F00VC01344 coupled with magnet assembly part number F00VC30319. The solenoid actuator regulates dynamic fuel displacement above the control plunger, balancing fluid pressure to govern needle lift across 1600 bar operating cycles.

QDoes this injector require ECU IMA coding?

Yes, ECU IMA (Injector Quantity Adjustment) coding is strictly required. Each injector features a factory-calibrated alphanumeric code laser-etched onto the solenoid connector cap, which defines minute manufacturing flow tolerances that the ECU uses to balance cylinder-to-cylinder torque, emission output, and idle smoothness.

QWhat are the common failure symptoms and associated DTC codes?

Common failure modes include elongated engine crank times, cylinder knock under load, unburnt fuel smoke, and dynamic power derate. Primary Diagnostic Trouble Codes include P0087 (Fuel Rail/System Pressure Too Low due to excessive control valve back-leakage), P0201 through P0204 (Injector Circuit Open/Short on cylinders 1–4), and cylinder contribution fault codes P1011 or P1012.

QWhat are the proper installation torque specifications?

The injector hold-down clamp bolt must be installed using a new stretch bolt and tightened according to the vehicle manufacturer specification (typically an initial 25–30 N·m or torque-angle sequence). The high-pressure inlet feed line nut requires 25–28 N·m while using a secondary counter-hold wrench on the injector inlet fitting.

QHow do you perform a dynamic back-leakage flow bench test?

Mount the injector on an ISO-compliant CRDI test bench to quantify fuel return volume at specific test steps: back-leakage at low-idle (250–300 bar) must not exceed 35 ml/min, and return flow at full-load (1600 bar) must remain under 50 ml/min. Higher return flow rates confirm severe seat erosion or micro-pitting on the F00VC01344 control valve face.

QWhat is the acceptable solenoid coil electrical resistance?

Using a calibrated digital milliohmmeter across the terminals of magnet assembly F00VC30319 at 20°C (68°F), the coil winding resistance must measure strictly between 0.25 and 0.50 ohms. Additionally, insulation resistance from either terminal to the metal injector outer body must exceed 100 megaohms at 500V DC.

QWhy is the two-wrench installation procedure strictly mandatory?

The two-wrench procedure isolates tightening torque to the external threaded connection. Without counter-holding the inlet fitting, tightening torque transfers through the injector body, shearing the internal locating alignment pins and distorting the precision-lapped sealing interface between the F00VC01344 valve seat, intermediate plate, and 0433171981 nozzle body.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0200Critical

Fuel Injector Circuit Malfunction (General / Common Driver Stage)

P0201Critical

Injector Circuit Malfunction - Cylinder 1

P0300Critical

Random or Multiple Cylinder Misfire Detected

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

Workshop Diagnostic Protocol

Common Rail Injector Back-Leak Testing Guide

Common rail injector backleak test protocol. Graduated cylinder setup, warm idle & cranking limits in mL/min, control valve wear & P0087 diagnosis.

Read Technical Protocol
ECU Calibration Protocol

Bosch IMA Injector Coding & Location Guide

Bosch common rail injector IMA coding guide. Locate laser-etched 6-9 digit codes on body, ECU OBD2 adaptation steps & test bench calibration facts.

Read Technical Protocol
COMMON RAIL DIESEL WORKSHOP SOP

Stuck Injector Removal & Carbon Cleaning SOP | FuelPartsDB

Comprehensive workshop SOP for stuck diesel injector removal, pneumatic vibro-puller extraction, carbon solvent softening, and seat reaming without damage.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol