BOSCH 0445115068
Piezo Common Rail Injector for Mercedes Sprinter / Vito 2.1 CDI OM646
A6460701487, 6460701487, A6460701187, 6460701187, A6460701587, 6460701587INTEGRATED PIEZO ACTUATOR (CRI3)F00VX200171600 bar peak rail pressureProduct Overview
The Bosch 0445115068 is an OEM common rail diesel fuel injector engineered for Mercedes-Benz commercial and passenger vehicles powered by the OM646 (2.1 CDI / 2.2 CDI, 2148 ccm inline-4) diesel engine. Operating at a peak rail pressure of 1600 bar, this CRI3 piezo unit features the high-precision F00VX20017 nozzle assembly and Integrated Piezo Actuator (CRI3) valve mechanism to deliver multiple micro-injections per combustion cycle. It fully complies with Euro 4 emissions standards. Direct replacement for OEM references A6460701487, 6460701487, A6460701187, 6460701187, A6460701587, 6460701587, and Bosch exchange 0986435356.
Always verify the OE cross-reference stamped on your failed injector body (A6460701487 / A6460701187 / A6460701587) prior to ordering. Bosch 0445115068 is a third-generation CRI3 piezo injector utilizing the F00VX20017 piezo nozzle assembly and Integrated Piezo Actuator calibrated to 1600 bar for Mercedes OM646 engines. Cylinder-specific IMA coding is mandatory after installation.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Mercedes-Benz Sprinter (W906) | OM646 / OM647 / OM648 | 2006-2009 |
| Mercedes-Benz Vito (W639) | OM646 / OM647 / OM648 | 2006-2010 |
| Mercedes-Benz Viano (W639) | OM646 / OM647 / OM648 | 2006-2010 |
Technical Specifications
| Specification | Value |
|---|---|
| SKU | 0445115068 |
| Brand | Mercedes-Benz / BOSCH |
| Type | Complete Injector Assembly (Bosch Common Rail (CRI3-16 piezo)) |
| OE Number | A6460701487 |
| Control ValveCore Spec | |
| Nozzle CodeCore Spec | |
| Nozzle Part NumberCore Spec | |
| Injection System | Bosch Common Rail (CRI3-16 piezo) |
| Operating PressureCore Spec | |
| Torque Spec | 28-30 N·m |
| Hold Down Torque | 7 N·m + 90° |
| Warranty | 12 Months |
| Emission Standard | Euro 4 |
| Engine Family | OM646 (2.1 CDI / 2.2 CDI) |
| Coding Required | Yes (IMA Code) |
Installation Tips
Tools needed: 10mm & 11mm flare nut wrench (rail and injector inlet unions), Injector slide hammer / mechanical puller kit (if seized), Injector seat cleaning brass brush set & industrial vacuum, Seat reaming tool (if carbon erosion is present), Torque wrench (2 N·m - 40 N·m range), ECU diagnostic scan tool with IMA/QR coding capability, Digital micrometer / depth gauge for copper washer check
- Disconnect Battery & Relieve Rail Pressure: Isolate negative battery terminal and verify rail residual pressure drops below 10 bar via live diagnostics before cracking fuel fittings.
- Clean Engine Bay & Injector Recesses: Thoroughly blast away grit, oil slurry, and loose dirt around cylinder head injector wells using compressed air and degreasing solvent.
- Label Wiring Harness & Spill-Off Connectors: Tag each cylinder harness connector and gently disengage delicate plastic spill-off return rail clips.
- Remove High-Pressure Supply Lines: Back off high-pressure union nuts with a flare-nut wrench; IMMEDIATELY cap all open fuel rail orifices and injector inlets with clean blanking caps.
- Extract Hold-Down Clamp Fasteners: Back out hold-down clamp bolts. Note that torque-to-yield stretch bolts must always be discarded and never reused.
- Extract Injector Body: Withdraw injector vertically. If carbon-bonded or coked, attach an approved mechanical slide-hammer puller to the inlet adaptor without rotating the injector body.
- Inspect Injector Well & Bore: Ensure old copper seal washer has not remained fused at the base of the cylinder head seat; remove with a brass retrieval pick if stuck.
- Clean & Ream Injector Seat: Ream and burnish injector seating face using dedicated seat cutter brushes and industrial vacuum until seat is 100% bare, flat metal.
- Install New Copper Sealing Washer: Mount an OEM-specification copper washer of designated thickness using high-temp grease to hold in position.
- Fit Injector with Ceramic Anti-Seize: Lightly coat the injector body barrel with approved high-temperature ceramic grease; keep nozzle tip and copper washer strictly dry and clean.
- Torque Hold-Down Clamp to Spec: Secure hold-down clamp bolts and torque to factory specified stages (7 N·m + 90°) using a calibrated torque wrench.
- Refit High-Pressure Delivery Pipes: Thread union nuts by hand to avoid cross-threading, then tighten injector inlet and rail unions to 28-30 N·m evenly.
- Reconnect Return Leak-Off Line & Harness: Push on leak-off return clips until retaining collars click home; reattach electrical plug and lock harness tab firmly.
- ECU IMA / QR Code Calibration & Fuel Priming: Program the unique alphanumeric IMA/QR calibration code etched on the injector head into the corresponding ECU cylinder address; prime fuel system prior to initial cranking.
- CRITICAL IMA CALIBRATION: Never operate the engine without programming the new IMA/QR trim code into the ECU map — uncalibrated injectors cause combustion knocking, cylinder imbalance, and premature DPF clogging.
- CRITICAL COPPER WASHER REPLACEMENT: Always install brand new copper crush washers and torque-to-yield clamp bolts — reusing old seals leads to catastrophic combustion gas leakage ('black death' buildup).
- HOSPITAL-GRADE FUEL CLEANLINESS: A microscopic contamination particle as small as 5 microns can jam the internal piezo valve or needle — ensure all fuel line plugs stay on until final connection.
- STRICT HOLD-DOWN TORQUE: Adhere strictly to the 7 N·m + 90° tightening sequence — overtightening distorts the injector body and binds the needle.
Frequently Asked Questions
Does Bosch injector 0445115068 require ECU coding (IMA / QR code)?
Yes, Bosch injector 0445115068 requires cylinder-specific IMA calibration code programming into the engine control unit (ECU). Each unit has a unique multi-character calibration code stamped on its electrical connector body that defines fuel delivery tolerances across multiple rail pressure points. Programming this code via a diagnostic scanner (Mercedes Star DAS / Xentry, or Autel MaxiSys) is mandatory to ensure balanced cylinder idle, proper emissions compliance, and smooth throttle response.
What are the most common symptoms of a failing 0445115068 injector on Mercedes Sprinter / Vito OM646?
Common symptoms include prolonged cold-start cranking, rough or oscillating idle, black exhaust smoke under acceleration (nozzle needle wear/over-fueling), ticking/clattering under load, increased fuel consumption, cylinder misfire trouble codes, and high fuel spill-off return rates causing rail pressure drops under heavy acceleration.
What is the difference between CRI2 solenoid (0445110137) and CRI3 piezo (0445115068) on the OM646?
The earlier Euro 3 / Euro 4 OM646 engines utilized CRI2 solenoid injectors such as 0445110137 with electromagnetic valves. Later production OM646 variants on the Sprinter W906 and Vito W639 upgraded to Bosch CRI3 piezo injectors (0445115068) featuring high-speed piezoelectric actuators with nozzle assembly F00VX20017. They operate on entirely different electrical driver stages in the ECU and are NOT interchangeable.
Why must the copper crush washer and hold-down bolt be replaced on every install?
The copper washer forms the critical gas-tight seal between the injector nozzle and the cylinder head combustion chamber. A compressed washer work-hardens and will not re-seal properly. Furthermore, Mercedes hold-down clamp bolts are torque-to-yield stretch fasteners designed for single use; reusing them risks bolt snapping inside the cylinder head or loss of clamp tension ('black death').
What preventative maintenance is required after installing replacement 0445115068 injectors?
Always replace the diesel fuel filter with a high-efficiency OEM-spec filter (3 to 5 micron rating), inspect the fuel tank and fuel lines for metallic swarf from high-pressure pump wear, flush the common rail if debris is present, use high-quality EN590 diesel, and verify injector smooth running balance values with diagnostic software after 500 km of driving.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.