Catalog / BOSCH / 13518604229
BOSCH

BOSCH 13518604229

View Specs
SolenoidGDI High-Pressure Fuel Pump (HPFP)Euro 6

High Pressure Fuel Pump BMW B58TU S58 M340i Supra A90 X3 M40i

Reference data for BOSCH 13518604229 high-pressure fuel pump · OEM 13517642466, 13518631642, 0261520281, 0261520282 · Application BMW B38 / B48 / B58 Modular TwinPower Turbo (1.5L / 2.0L / 3.0L & TU)
OE REFERENCE13517642466, 13518631642, 0261520281, 0261520282
CONTROL VALVEINTEGRATED HIGH-SPEED DIGITAL FLOW CONTROL VALVE (MSV)
NOZZLE-
EMISSIONEuro 6
WARRANTY12 Months
01

Product Overview

The Bosch 13518604229 (Bosch 0261520281 / BMW OE 13518631642) is the factory original equipment 350 bar high-pressure mechanical fuel pump for BMW B58 Technical Update (B58TU) and S58 high-performance inline-six engines. Featuring an upgraded internal barrel and DLC-coated plunger, it atomizes fuel to sub-6-micron droplet diameter for optimal flame velocity and zero particulate wall-wetting. Worn units cause severe high-RPM fuel pressure drop, cutouts at peak boost, and DTCs P0087 and P0089.

Before You Order

Always verify the OE reference 13517642466, 13518631642 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 13518604229 needs no ECU calibration coding; no code transfer is required after fitting.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
BMW M340i G20BMW B38 / B48 / B58 Modular TwinPower Turbo (1.5L / 2.0L / 3.0L & TU)2020-2024
Toyota GR Supra 3.0BMW B38 / B48 / B58 Modular TwinPower Turbo (1.5L / 2.0L / 3.0L & TU)2020-2024
BMW M3 G80BMW B38 / B48 / B58 Modular TwinPower Turbo (1.5L / 2.0L / 3.0L & TU)2021-2024
04

Technical Specifications

SpecificationValue
Pump GenerationBosch HDP-5-Evo Single-Piston High-Pressure Mechanical Fuel Pump
Operating Rail PressureCore Spec
Cam Drive TypeExhaust Camshaft Tri-Lobe via DLC Roller Follower
Flow Regulation ControlIntegrated High-Speed Digital Flow Control Valve (MSV)
Pump Flange Mounting Torque13 N·m (Even alternating pass)
High Pressure Pipe Flare Nut Torque30 N·m
Tightening Torque30 N·m
Primary OEM Reference13518604229, 13517642466, 13518631642, 0261520281
Engine Emission ComplianceEuro 6d-TEMP / Euro 6d / LEV III Tier 3
Standard Industrial Warranty12 Months / Unlimited Mileage
05

Installation Tips

Tools needed: E-Torx socket set (E8 / E10) and 1/4-inch drive torque wrench, 14mm and 17mm line flare wrenches for high-pressure fuel rail connections, Clean engine assembly lubricant for cam follower and O-ring seal, Absorbent shop towels and eye safety goggles for fuel containment

  1. Disconnect vehicle 12V battery; pull fuel pump module fuse and crank engine for 5 seconds to discharge low-pressure system.
  2. Wrap fuel line unions in lint-free shop towels; slowly loosen line flare nuts to vent residual 350 bar rail pressure.
  3. Disconnect electrical connector from the quantity control solenoid valve.
  4. Release low-pressure fuel supply hose quick-connector from the pump inlet barb.
  5. Loosen the two E-Torx mounting bolts gradually and alternately, half a turn at a time, preventing internal spring binding.
  6. Remove high-pressure pump from cylinder head; extract the roller follower and inspect the cam lobe for any scuff marks.
  7. Thoroughly clean the mounting bore and cylinder head surface; lubricate new pump O-ring and roller follower with clean engine oil.
  8. Rotate engine crankshaft until the camshaft drive lobe is at lowest lift (base circle).
  9. Insert lubricated roller follower; position pump assembly straight into bore and thread mounting bolts finger-tight.
  10. Torque mounting bolts evenly in alternating passes to 13 N·m.
  11. Hand-thread high-pressure pipe flare nuts to ensure thread alignment; torque unions to 30 N·m.
  12. Reconnect electrical plug and low-pressure supply hose; cycle ignition on 3 times to bleed air before engine start.
Tips & Warnings:
  • Extreme Rail Pressure Notice: Always allow engine to sit for 30 minutes after shutdown before cracking high-pressure fittings to let static rail pressure decay safely.
  • Torque Balance Rule: Tighten mounting bolts strictly alternating half a turn per bolt; uneven tightening will fracture the alloy mounting lugs.
06

Frequently Asked Questions

QWhat are the primary symptoms when 13518604229 fails?

Primary symptoms include extended cold engine cranking, severe hesitation under wide-open throttle, rough idle RPM fluctuation, and Diagnostic Trouble Codes P0087 (Fuel Rail/System Pressure Too Low), P0089 (Fuel Pressure Regulator Performance), or P0300 (Random/Multiple Cylinder Misfire).

QWhat is the exact tightening torque for 13518604229?

The holding flange mounting torque is 13 N·m, and the high-pressure fuel pipe union nut must be torqued to 30 N·m.

QCan I reuse the seals when replacing 13518604229?

No. All high-pressure fuel seals, including Viton O-rings and combustion chamber Teflon rings, are strictly single-use. Reusing compressed seals will cause pressurized fuel leaks or combustion blowby into the cylinder head.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0088Critical

Fuel Rail/System Pressure Too High

P0089Critical

Fuel Pressure Regulator 1 Performance

P0191Critical

Fuel Rail Pressure Sensor 'A' Circuit Range/Performance

P0002High

Fuel Volume Regulator Control Circuit Range / Performance (VCV / IMV)

P0090High

Fuel Pressure Regulator 1 Control Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

COMMON RAIL WORKSHOP DIAGNOSTICS

Common Rail High-Pressure Pump Diagnostics Guide

Diagnose common rail high-pressure pump failure: suction vacuum, CP4 roller glitter, plunger wear, air ingress & P0087 hard start. Workshop bench testing.

Read Technical Protocol
COMMON RAIL WORKSHOP DIAGNOSTICS

Fuel Metering Valve (IMV/SCV) Diagnostics Guide

Diagnostic guide for common rail fuel metering valves (IMV/SCV/FCA/MPROP). Normally open vs closed, coil resistance, PWM duty cycle & P0088 / P0089 test.

Read Technical Protocol
OBD-II DIAGNOSTIC PROTOCOL

P0087 Low Rail Pressure Diagnosis Guide

Step-by-step workshop diagnostic protocol for OBD-II DTC P0087 (Fuel Rail Pressure Too Low). 5-stage troubleshooting tree: backleak testing, SCV valve, PRV valve, and high-pressure pump.

Read Technical Protocol
COMMON RAIL WORKSHOP DIAGNOSTICS

Rail Pressure Relief Valve Diagnostics Guide

Common rail pressure relief valve (PRV) testing guide. Diagnose hot start stalls, P0087 rail pressure loss, return line leakage & single vs 2-stage valves.

Read Technical Protocol