BOSCH 13517847204
High Pressure Fuel Pump BMW M3 F80 M4 F82 F83 M2 CS F87 3.0T Biturbo S55 0261520282
7847204, 13517850257, 7850257, 0261520282--200 bar peak rail pressureProduct Overview
The 13517847204 is an original equipment (BOSCH) precision component engineered specifically for the BMW M TwinPower Turbo 3.0L Inline-6 DOHC 24V S55 (S55B30A). Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P10F3, P0171.
Always verify the OE reference 7847204, 13517850257, 7850257 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 13517847204 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 13517847204 |
| Manufacturer Brand | BOSCH |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | BMW M TwinPower Turbo 3.0L Inline-6 DOHC 24V S55 (S55B30A) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 13 N-m (115 lb-in) |
| Fuel Line / Rail Torque | 30 N-m (22 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P10F3, P0171 |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 13 N-m (115 lb-in), and torque fuel line fittings to 30 N-m (22 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Verify part number 13517847204 and cross references 7847204, 13517850257, 7850257, 0261520282, and 0261500109 before installation.
- Tighten the pump mounting/hold-down fasteners to 13 N·m.
- Tighten the high-pressure line to 30 N·m.
Frequently Asked Questions
Will this high-pressure fuel pump fit my BMW?
Part number 13517847204 is listed for BMW N20, N26, N55, and S55 2.0L & 3.0L TwinPower Turbo engines. It is listed for BMW 3 Series F30/F31 2012-2016, 5 Series F10/F11 2011-2017, X3 F25/X4 F26 2011-2017, and X5 F15/X6 F16 2014-2018. Confirm fitment against the vehicle’s EPC before ordering.
What diagnostic trouble codes are listed for this pump?
The verified diagnostic trouble codes listed for this high-pressure fuel pump are P0300, P0087, P0193, P0089, and P0191. Symptom descriptions are not stated in the supplied facts, so confirm diagnosis against the vehicle’s EPC/service information instead of guessing.
Does this pump require coding or adaptation after installation?
No coding or adaptation requirement is stated in the verified facts for part 13517847204. Confirm the required procedure for the specific BMW against the vehicle’s EPC/service information before installation.
Can I reuse the seals when replacing this pump?
Reuse of seals is not stated in the verified facts for this high-pressure fuel pump. Confirm seal replacement requirements against the vehicle’s EPC/service information instead of guessing.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.