Catalog / MOPAR / 05038533AA
MOPAR

MOPAR 05038533AA

View Specs
SolenoidMulti-Point Port Fuel Injection (MPI / EV14)Euro 5

Multi Port Fuel Injector Dodge Ram 1500 Charger Challenger Durango Jeep Grand Cherokee 5.7L V8 HEMI 68211173AA

Reference data for MOPAR 05038533AA common rail injector · OEM 68211173AA, 05038533AB, 5038533AA, RL038533AA, 280158233, FJ1080, 0280158233 · Application Chrysler/Dodge 5.7L HEMI V8 OHV 16-Valve VVT MDS (Eagle Architecture, EZH/EZC)
OE REFERENCE68211173AA, 05038533AB, 5038533AA, RL038533AA, 280158233, FJ1080, 0280158233
CONTROL VALVEHIGH-EFFICIENCY 4-HOLE PRECISION ATOMIZATION DIRECTOR PLATE
NOZZLE4-Hole Precision Calibrated Stainless Steel Director Plate
EMISSIONEuro 5
WARRANTY12 Months
01

Product Overview

The Mopar 05038533AA (superseding part number 68211173AA, Bosch engineering reference 0280158233, standard motor FJ1080) is the original equipment multi-port electronic fuel injector (MPI/EFI) engineered for Chrysler, Dodge, Ram, and Jeep 5.7-liter V8 HEMI engines equipped with Variable Valve Timing (VVT Eagle architecture). Calibrated for 58 psi (4.0 bar) fuel rail pressures and delivering a static flow rate of 34.8 lb/hr (365 cc/min), this high-impedance saturated injector fuels millions of trucks and performance passenger vehicles including the Ram 1500, Dodge Charger, Challenger, Durango, and Jeep Grand Cherokee. As mileage accumulates, ethanol blended gasoline creates gum, varnish, and carbon deposits on the 4-hole director plate. Symptoms include poor fuel atomization, hot-soak extended cranking times, cylinder misfire codes P0300 (Random/Multiple Cylinder Misfire), specific cylinder misfires (P0301 through P0308), rough idle vibration, and system lean trouble codes P0171 / P0174. In severe cases, an injector stuck open washes cylinder wall lubrication and risks catalytic converter overheating. Replacement demands precision installation standards. Technicians must inspect manifold injector bores, lubricate fresh Viton O-rings with clean motor oil or silicone lubricant, and verify clip engagement. Rail fasteners threading into the composite intake manifold must be torqued to 9 N·m (80 in-lb). After installation, cycle the ignition key three times to verify rail pressure integrity prior to engine cranking.

Before You Order

Always verify the OE reference 68211173AA, 05038533AB, 5038533AA, RL038533AA stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 05038533AA needs no ECU calibration coding; no code transfer is required after fitting.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Ram 1500 / 2500EZH / EZC2009-2024
Dodge Durango 5.7L HEMIEZH / EZC2009-2024
Dodge Charger / ChallengerEZH / EZC2009-2023
Jeep Grand Cherokee (WK2)EZH / EZC2009-2023
Chrysler 300 / 300CEZH / EZC2009-2023
04

Technical Specifications

SpecificationValue
System TypeChrysler Multi-Port Electronic Fuel Injection (MPI / EFI) System
Operating Fuel Pressure4.0 bar (58 psi / 400 kPa regulated)
Static Flow Rate34.8 lb/hr @ 58 psi (365 cc/min @ 400 kPa)
Electrical Resistance12.0 - 14.5 Ohms @ 20°C (High-Impedance Saturated Solenoid)
Nozzle AtomizerCore Spec
Fuel Rail Fastener Torque9 N·m (80 in-lb) composite intake manifold rail bolts
Upper & Lower O-RingsHigh-Durability Fluorosilicone (FKM) Viton Material
ManufacturerBosch / Mopar (Tier-1 OEM for Stellantis / Chrysler Group LLC)
Bosch Production Reference0280158233
05

Installation Tips

  1. Fuel Rail Depressurization & Battery Ground Disconnect: Depress Schrader test valve on passenger-side fuel rail with shop rag to bleed residual 58-psi pressure. Disconnect negative battery cable terminal.
  2. Air Cleaner Intake Tube & Engine Cover Removal: Loosen intake resonator hose clamps, remove air filter box tube, and unclip plastic HEMI engine appearance acoustic beauty cover.
  3. Injector Electrical Connector & Rail Retaining Bolt Removal: Slide red CPA locking tabs out and disconnect all 8 injector harness plugs. Remove the four 10mm fuel rail retaining bolts securing rails to the composite manifold.
  4. Fuel Rail Extraction & Injector Retaining Clip Removal: Pull fuel rail straight up and out. Slide metal retaining spring clips off each injector body and twist injectors free from the rail cups.
  5. Lubrication, Insertion & Rail Fastener Torquing: Lightly lubricate new upper and lower Viton O-rings with clean engine oil or silicone grease. Seat injectors firmly into rail, install clips, and torque rail bolts to 9 N·m (80 in-lb).
Tips & Warnings:
  • Never use petroleum jelly or brake cleaner on O-rings: Use clean engine oil or silicone spray; harsh solvents degrade Viton fluorosilicone causing intake manifold air leaks.
  • Inspect intake manifold injector pockets: Remove grit and carbon buildup from the composite manifold injector bores before pressing new injectors in to ensure airtight vacuum sealing.
  • Verify injector retaining clip alignment: Ensure injector clips snap into the recessed groove on both the injector body and the rail collar to prevent pressure blow-off.
  • Check for fuel leaks before restarting: Cycle key to RUN position three times without cranking to pressurize system to 58 psi and inspect rails for weeping.
06

Frequently Asked Questions

QWill this injector fit my Ram, Durango, Charger, Challenger, or Grand Cherokee?

It is listed for the Chrysler/Dodge HEMI applications shown for Ram, Durango, Charger, Challenger, and Jeep Grand Cherokee. Confirm your exact engine code and VIN against the EPC before ordering 05038533AA.

QWhat symptoms suggest the injector has failed?

Look for a misfire, rough idle, hesitation, poor fuel economy, or a petrol smell. A failed multi-point injector can also cause a dead cylinder or imbalance. Confirm diagnosis with scan data and injector testing before replacing 05038533AA.

QWhat should I check before ordering this injector?

Verify the existing injector part number, engine code, and vehicle application against the EPC. Check connector type and rail fitment, and confirm whether any coding or adaptation is required in the workshop manual before ordering 05038533AA.

QDoes the replacement injector need to be matched or adapted?

Adaptation or coding requirements are not stated in the product data. Check the vehicle's EPC and workshop manual for the required procedure, and confirm correct part number 05038533AA for your application before installation.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0200Critical

Fuel Injector Circuit Malfunction (General / Common Driver Stage)

P0201Critical

Injector Circuit Malfunction - Cylinder 1

P0300Critical

Random or Multiple Cylinder Misfire Detected

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

Workshop Diagnostic Protocol

Common Rail Injector Back-Leak Testing Guide

Common rail injector backleak test protocol. Graduated cylinder setup, warm idle & cranking limits in mL/min, control valve wear & P0087 diagnosis.

Read Technical Protocol
COMMON RAIL DIESEL WORKSHOP SOP

Stuck Injector Removal & Carbon Cleaning SOP | FuelPartsDB

Comprehensive workshop SOP for stuck diesel injector removal, pneumatic vibro-puller extraction, carbon solvent softening, and seat reaming without damage.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol