Catalog / MOPAR / 5184085AC
MOPAR

MOPAR 5184085AC

View Specs
SolenoidMulti-Point Port Fuel Injection (MPI / EV14)Euro 6

Multi Port Fuel Injector Jeep Grand Cherokee Wrangler Dodge Charger Challenger Durango Ram 1500 3.6L Pentastar V6

Reference data for MOPAR 5184085AC common rail injector · OEM 5184085AD, 05184085AD, 280158233, FJ1147, RL184085AC, 0280158233 · Application Chrysler / Stellantis 3.6L Pentastar DOHC 24V V6 (ERB / ERC)
OE REFERENCE5184085AD, 05184085AD, 280158233, FJ1147, RL184085AC, 0280158233
CONTROL VALVE4-HOLE PRECISION CONE SPRAY ATOMIZATION DIRECTOR
NOZZLE-
EMISSIONEuro 6
WARRANTY12 Months
01

Product Overview

The Mopar 5184085AC (superseding part number 5184085AD, alternate references 05184085AC, 05184085AD, Bosch production code 0280158233, and aftermarket code FJ1147) is the genuine factory multi-port fuel injector engineered for Stellantis's ubiquitous 3.6-liter Pentastar V6 engine. Operating at 58 psi (4.0 bar) fuel pressure with an optimized 4-hole conical spray pattern, this high-impedance fuel injector delivers precision metering across more than 10 million vehicles worldwide, including the Jeep Grand Cherokee (WK2), Wrangler (JK/JL), Gladiator (JT), Dodge Charger, Challenger, Durango, Ram 1500, Chrysler 300, and Pacifica. Over extended operational mileage, fuel deposits and fuel gum varnish coat the internal pintle orifice and microscopic filter screen. The resulting fuel delivery imbalance causes cylinders to run excessively lean. Typical customer complaints include rough idle vibration at red lights, engine hesitation upon tip-in throttle acceleration, check engine light flashing under load, and diagnostic trouble codes P0300 (Random/Multiple Cylinder Misfire), specific cylinder misfires (P0301 through P0306), and lean fuel trim codes P0171 and P0174. Replacing injectors requires removal of the upper composite intake manifold plenum. Technicians must renew both the upper and lower Viton O-rings and replace the 6-pack plenum port gaskets. The fuel rail retaining bolts must be torqued to 8 N·m (71 in-lb), and the intake manifold plenum bolts tightened to 10 N·m (89 in-lb). Confirming that injectors rotate freely in their sockets prior to tightening the rail ensures perfect seal alignment.

Before You Order

Always verify the OE reference 5184085AD, 05184085AD, 280158233, FJ1147 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 5184085AC needs no ECU calibration coding; no code transfer is required after fitting.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Jeep Grand Cherokee (WK2) / Wrangler (JL)Chrysler / Stellantis 3.6L Pentastar DOHC 24V V6 (ERB / ERC)2011-2023
Dodge Charger / Challenger / DurangoChrysler / Stellantis 3.6L Pentastar DOHC 24V V6 (ERB / ERC)2011-2023
Ram 1500 (Classic/DT)Chrysler / Stellantis 3.6L Pentastar DOHC 24V V6 (ERB / ERC)2013-2023
04

Technical Specifications

SpecificationValue
System TypeChrysler Pentastar Multi-Point Electronic Fuel Injection (MPI)
Operating Fuel Pressure4.0 bar (58 psi / 400 kPa regulated rail pressure)
Static Fuel Flow Rate245 g/min @ 4.0 bar (approximately 235 cc/min @ 3 bar)
Electrical Resistance12.0 - 13.0 Ohms @ 20°C (High-Impedance Saturated Solenoid)
Spray Geometry4-Hole Precision Multi-Dispersal Cone Pattern
Fuel Rail Fastener Torque8 N·m (71 in-lb) fuel rail mounting bolts into lower intake
Upper Intake Plenum Fasteners10 N·m (89 in-lb) composite intake manifold fasteners
Seals ArchitectureUpper & Lower High-Fluorine Viton Chemical-Resistant O-Rings
ManufacturerBosch / Mopar (Tier-1 OEM for Stellantis)
Bosch Production Reference0280158233
05

Installation Tips

  1. Fuel System Residual Pressure Depressurization: Remove fuel pump relay or fuse in TIPM / PDC power distribution center under the hood. Crank engine until it stalls to exhaust line pressure, then disconnect negative battery terminal.
  2. Upper Composite Intake Manifold Plenum Removal: Disconnect PCV breather hoses, throttle body electrical plug, and unbolt upper composite intake manifold. Remove upper plenum to access fuel rails in the cylinder valley.
  3. Fuel Rail Fastener Removal & Rail Extraction: Disconnect electrical harness connector clips from each injector. Remove four 8mm fuel rail mounting bolts. Lift fuel rail straight up and extract injectors from lower intake pockets.
  4. Lower Manifold Bores Inspection & Cleaning: Clean dirt and grit from lower manifold injector bores using lint-free cloths to prevent debris from falling into the combustion chambers.
  5. New Viton O-Ring Lubrication, Installation & Sequence Torquing: Lubricate new upper and lower Viton O-rings with clean engine oil. Press injectors into rail cups with retaining clips. Torque fuel rail bolts to 8 N·m (71 in-lb) and upper intake manifold bolts to 10 N·m (89 in-lb).
Tips & Warnings:
  • Inspect injector retaining wire clips: Ensure retaining clips securely lock the injector shoulder into the fuel rail cup; improper clip engagement allows the injector to pop out under 58 psi rail pressure.
  • Always replace lower plenum intake gaskets: The teal silicone upper-to-lower intake manifold gaskets harden and flatten; reuse causes unmetered intake vacuum leaks and P0171/P0174 codes.
  • Never use silicone grease on O-rings: Coat strictly with clean engine oil or clean transmission fluid; silicone will damage upstream oxygen sensors.
  • Tighten intake manifold fasteners in crisscross sequence: Torque upper intake manifold fasteners in alternating center-outward sequence to 10 N·m (89 in-lb) to prevent warping the composite plastic.
06

Frequently Asked Questions

QWhich vehicles does 5184085AC fit?

5184085AC fits the listed Pentastar applications: Jeep Grand Cherokee and Wrangler JL; Dodge Charger, Challenger and Durango; and Ram Classic/DT. Confirm your vehicle against the EPC before ordering.

QWhat should I check before ordering 5184085AC?

Check the vehicle's EPC or workshop manual for the correct injector application and any coding or adaptation requirements. Confirm the existing unit's part number and engine family before ordering 5184085AC.

QDoes the old injector need to be matched or adapted?

Matching or adaptation requirements are not stated in this listing. Confirm against the vehicle's EPC or workshop manual whether the replacement injector needs coding or adaptation after installation.

QWhat should I do if I suspect the injector has failed?

This listing does not describe failure symptoms. For driveability complaints, diagnose against the vehicle's workshop data and confirm the injector is faulty before replacing it with 5184085AC.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0200Critical

Fuel Injector Circuit Malfunction (General / Common Driver Stage)

P0201Critical

Injector Circuit Malfunction - Cylinder 1

P0300Critical

Random or Multiple Cylinder Misfire Detected

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

Workshop Diagnostic Protocol

Common Rail Injector Back-Leak Testing Guide

Common rail injector backleak test protocol. Graduated cylinder setup, warm idle & cranking limits in mL/min, control valve wear & P0087 diagnosis.

Read Technical Protocol
COMMON RAIL DIESEL WORKSHOP SOP

Stuck Injector Removal & Carbon Cleaning SOP | FuelPartsDB

Comprehensive workshop SOP for stuck diesel injector removal, pneumatic vibro-puller extraction, carbon solvent softening, and seat reaming without damage.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol