BOSCH 05184085AC
Multi Hole Fuel Injector Jeep Wrangler Grand Cherokee Dodge Charger 3.6L Pentastar 0280158233
05184085AD, 5184085AD, 0280158234, FJ1147, RL184085AC, 0280158233--4 bar peak rail pressureProduct Overview
The BOSCH 05184085AC is a factory precision fuel injection component engineered specifically for the Chrysler 3.6L Pentastar DOHC 24V V6 (ERC / ERB / EHL). Manufactured to strict original equipment tolerances, it delivers precise fuel atomization and operates up to its rated pressure of 4.0 bar (58 psi). Common operational failure symptoms that point directly to this assembly include: Persistent Diagnostic Trouble Codes such as P0300, P0301, P0171, P0174 stored in the ECM. Hard cold starting, erratic idle oscillations, and severe acceleration stumbling. Unburnt fuel smell in the exhaust, black tailpipe soot, or fuel dilution in the engine crankcase. Loss of high-RPM power and engine protection limp-mode activation under highway load.
Always verify the OE reference 05184085AD, 5184085AD, 0280158234, FJ1147 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 05184085AC needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| sku | 05184085AC |
| brand | BOSCH |
| manufacturer_code | 0280158233 |
| pressure_rating | 4.0 bar (58 psi) |
| torque_flange | 7 N-m (62 lb-in) |
| torque_line | 10 N-m (89 lb-in) |
| engine_family | Chrysler 3.6L Pentastar DOHC 24V V6 (ERC / ERB / EHL) |
Installation Tips
- Always replace single-use high-pressure fuel lines and Teflon/copper sealing washers before installation.
- Lubricate the pump roller tappet or injector O-rings with clean engine oil before guiding into place.
- Tighten mounting flange fasteners in an even criss-cross pattern to 7 N-m (62 lb-in).
- Hand-thread fuel rail fittings first, then torque high-pressure flare nuts to 10 N-m (89 lb-in) using a calibrated crowfoot wrench.
- Cycle the low-pressure fuel pump multiple times and perform a physical leak inspection before engine ignition.
- Before installation, confirm the replacement injector is 05184085AC and that the application matches the vehicle’s EPC data.
- Inspect the injector bore and connector, and confirm seal and retainer reuse guidance against the workshop manual before installation.
- After repair, verify correct seating and connection, then confirm any leak, adaptation or relearn checks in the vehicle’s workshop data.
Frequently Asked Questions
Will this injector fit my vehicle?
It is listed for Chrysler / Stellantis Pentastar DOHC applications in Jeep Grand Cherokee and Wrangler, Dodge Charger, Challenger and Durango, and Ram Classic/DT fitments. Confirm your engine code and VIN against the EPC before ordering.
What should I check before ordering?
Confirm the vehicle’s engine code, injector location and connector style against the EPC or workshop manual, and verify the old part marking matches 05184085AC. Do not rely on appearance alone.
Do I need to code or adapt the new injector?
The listing does not state coding or adaptation requirements. Check the vehicle’s EPC or workshop manual for the required procedure, and confirm whether any relearn or matching step applies before installation.
What are symptoms of a failed injector?
The product data does not list failure symptoms. Diagnose misfire, rough running, fuel odor or power loss using the vehicle’s workshop manual, and confirm the injector is faulty before replacing part 05184085AC.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.