Catalog / CONTINENTAL / 06L906036K
CONTINENTAL

CONTINENTAL 06L906036K

View Specs
SolenoidMulti-Point Port Fuel Injection (MPI / EV14)Euro 6

Port Fuel Injector VW Audi EA888 Gen 3B 2.0 TSI MPI

Reference data for CONTINENTAL 06L906036K common rail injector · OEM 06L906036D, 06L906036J, 06L906036L, A2C91277100 · Application Volkswagen / Audi EA888 Gen 3 & Gen 3B (1.8L & 2.0L TSI / TFSI CHHB / CJXC / CYFB)
OE REFERENCE06L906036D, 06L906036J, 06L906036L, A2C91277100
CONTROL VALVE12-HOLE WIDE-ANGLE ATOMIZATION PORT INJECTOR VALVE
NOZZLE12-Hole Precision Multi-Hole Spray Diffuser
EMISSIONEuro 6
WARRANTY12 Months
01

Product Overview

The Continental 06L906036K (VAG OE 06L906036D / 06L906036J / A2C91277100) is the genuine original equipment low-pressure multi-point port fuel injector for Volkswagen and Audi EA888 Gen 3B 2.0 TSI and TFSI dual-injection engines. Installed in the composite intake manifold rail operating at 4.0 to 7.0 bar, its 12-hole precision nozzle delivers fine atomization to prevent cold-start carbon deposits and optimize part-throttle fuel economy. Leaking or clogged injectors trigger P0171 (lean bank 1) or P0300 random misfires.

Before You Order

Always verify the OE reference 06L906036D, 06L906036J, 06L906036L, A2C91277100 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 06L906036K needs no ECU calibration coding; no code transfer is required after fitting.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Volkswagen Golf GTI MK7.5Volkswagen / Audi EA888 Gen 3 & Gen 3B (1.8L & 2.0L TSI / TFSI CHHB / CJXC / CYFB)2018-2024
Audi A4 (B9)Volkswagen / Audi EA888 Gen 3 & Gen 3B (1.8L & 2.0L TSI / TFSI CHHB / CJXC / CYFB)2016-2023
Audi Q5 (FY)Volkswagen / Audi EA888 Gen 3 & Gen 3B (1.8L & 2.0L TSI / TFSI CHHB / CJXC / CYFB)2018-2024
04

Technical Specifications

SpecificationValue
Injector TypeContinental Multi-Point Port Fuel Injector (MPI)
Operating Manifold Pressure4.0 to 7.0 bar (58 to 101 psi)
Nozzle Atomization Hole PatternCore Spec
Coil Resistance Value12.0 to 14.5 Ohms at 20°C (High Impedance)
Manifold Rail Bolt Torque9 N·m (Even progressive pass)
Tightening Torque9 N·m
Hold Down Torque9 N·m
Primary OEM Reference06L906036K, 06L906036D, 06L906036J, 06L906036L
Engine Emission ComplianceEuro 6d / WLTP / LEV III Tier 3
Standard Industrial Warranty12 Months / Unlimited Mileage

Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)

Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.

BOSCHExact Engine & Chassis Match
0261520288
Gasoline Direct Injection (GDI) • 200 bar
🚙 Engine Code CHHB
Technical Specifications & Pinout
BOSCHExact Engine & Chassis Match
06K127025D
Gasoline Direct Injection (GDI) • 200 bar
🚙 Engine Code CHHB
Technical Specifications & Pinout
BOSCHExact Engine & Chassis Match
06L127026A
Gasoline Direct Injection (GDI) • 250 bar
🚙 Engine Code CHHB
Technical Specifications & Pinout
05

Installation Tips

Tools needed: Torx T30 socket and 1/4-inch drive torque wrench for fuel rail bolts, O-ring pick for old seal removal, Silicone O-ring assembly grease (dielectric or clean mineral oil), Clean lint-free shop cloths for intake port protection

  1. Disconnect vehicle battery negative terminal; relieve low-pressure line pressure via Schrader service valve or fuel pump fuse removal.
  2. Disconnect electrical wiring harness connectors from all 4 port fuel injectors.
  3. Remove the two T30 Torx mounting fasteners securing the composite port fuel rail to the intake manifold.
  4. Gently rock the fuel rail assembly backward to pull all 4 injectors evenly from their manifold port sockets.
  5. Remove retaining clips holding injectors to the fuel rail; pull injectors from rail cups.
  6. Clean fuel rail cups and manifold injector ports with lint-free wipes; inspect for debris.
  7. Fit brand new upper and lower Viton O-rings onto each new injector; lubricate O-rings lightly with clean silicone grease.
  8. Insert injectors into fuel rail cups ensuring correct alignment tab orientation; reinstall metal retaining clips securely.
  9. Seat the complete injector rail assembly squarely into the intake manifold sockets until fully seated.
  10. Install T30 rail mounting bolts and torque evenly to 9 N·m.
  11. Reconnect injector wiring harness connectors until locking tabs click.
  12. Turn ignition on for 10 seconds without cranking to pressurize low-pressure fuel rail; inspect all 4 injector seats for leaks.
Tips & Warnings:
  • O-Ring Lubrication Mandate: Never install Viton O-rings dry; dry assembly will pinch or tear the rubber seal, causing dangerous pressurized fuel leaks on the intake manifold.
  • Retaining Clip Inspection: Ensure injector metal retaining clips snap fully into the rail grooves to prevent injector push-out under fuel pulse pressure.
06

Frequently Asked Questions

QWhat are the primary symptoms when 06L906036K fails?

Primary symptoms include extended cold engine cranking, severe hesitation under wide-open throttle, rough idle RPM fluctuation, and Diagnostic Trouble Codes P0087 (Fuel Rail/System Pressure Too Low), P0089 (Fuel Pressure Regulator Performance), or P0300 (Random/Multiple Cylinder Misfire).

QWhat is the exact tightening torque for 06L906036K?

The holding flange mounting torque is 9 N·m, and the high-pressure fuel pipe union nut must be torqued to 9 N·m.

QCan I reuse the seals when replacing 06L906036K?

No. All high-pressure fuel seals, including Viton O-rings and combustion chamber Teflon rings, are strictly single-use. Reusing compressed seals will cause pressurized fuel leaks or combustion blowby into the cylinder head.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0200Critical

Fuel Injector Circuit Malfunction (General / Common Driver Stage)

P0201Critical

Injector Circuit Malfunction - Cylinder 1

P0300Critical

Random or Multiple Cylinder Misfire Detected

P0301Critical

Cylinder 1 Misfire Detected

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

CRDI WORKSHOP ENGINEERING & DIAGNOSTICS

Piezo Injector 10 Bar Backleak & Stalling Guide

Bosch CRI3 piezo injector 10 bar backleak pressure guide. Diagnose hydraulic coupler cavitation, overflow valve failure, return line stalling & P0087.

Read Technical Protocol
ECU Calibration Protocol

Bosch IMA Injector Coding & Location Guide

Bosch common rail injector IMA coding guide. Locate laser-etched 6-9 digit codes on body, ECU OBD2 adaptation steps & test bench calibration facts.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol
COMMON RAIL DIESEL WORKSHOP SOP

Stuck Injector Removal & Carbon Cleaning SOP | FuelPartsDB

Comprehensive workshop SOP for stuck diesel injector removal, pneumatic vibro-puller extraction, carbon solvent softening, and seat reaming without damage.

Read Technical Protocol