Catalog / BOSCH / 06K127025D
BOSCH

BOSCH 06K127025D

View Specs
SolenoidGDI High-Pressure Fuel Pump (HPFP)Euro 6

High Pressure Fuel Pump VW Golf GTI R Audi S3 A4 Q5 2.0 TSI TFSI EA888 Gen 3 0261520197

Reference data for BOSCH 06K127025D high-pressure fuel pump · OEM 06K127025, 06K127025J, 06K127025G, 261520197, 261520198, GDP209, 0261520197, 0261520198 · Application Volkswagen / Audi EA888 Gen 3 & Gen 3B (1.8L & 2.0L TSI / TFSI CHHB / CJXC / CYFB)
OE REFERENCE06K127025, 06K127025J, 06K127025G, 261520197, 261520198, GDP209, 0261520197, 0261520198
CONTROL VALVEINTEGRATED HIGH-SPEED DIGITAL FLOW CONTROL SOLENOID
NOZZLE-
EMISSIONEuro 6
WARRANTY12 Months
01

Product Overview

The Bosch 06K127025D (Bosch reference 0261520197, superseding revisions 06K127025 and 06K127025J) is the authentic Tier-1 original equipment mechanical high-pressure fuel pump (HPFP) engineered for Volkswagen and Audi's renowned third-generation EA888 2.0-liter TSI and TFSI turbocharged engines. Generating rail pressures up to 200 bar (2900 psi), this camshaft-actuated single-plunger pump provides fuel metering across enthusiast platforms including the VW Golf GTI Mk7/Mk7.5, Golf R, Audi S3 (8V), Audi A4 (B9), and Audi Q5. Common failure symptoms observed on performance EA888 Gen 3 vehicles include fuel pressure rail drops under wide-open throttle, EPC (Electronic Power Control) dashboard illumination, extended cranking, and diagnostic trouble code P0087 (Fuel Rail/System Pressure Too Low). In severe instances, internal plunger lip seal deterioration allows high-pressure gasoline to weep past the piston shaft into the cylinder head camshaft gallery, creating severe crankcase fuel dilution, strong fuel odor on the dipstick, and reduced oil viscosity. Correct replacement requires careful adherence to VAG workshop manuals. The mounting flange Torx bolts must be tightened alternately and cross-torqued to 20 N·m (15 lb-ft), while the high-pressure steel fuel pipe union nut requires 27 N·m (20 lb-ft). Technicians should always replace the internal roller tappet and change engine oil and filter if fuel dilution is verified.

Before You Order

Always verify the OE reference 06K127025, 06K127025J, 06K127025G, GDP209 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 06K127025D needs no ECU calibration coding; no code transfer is required after fitting.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Volkswagen GolfVolkswagen / Audi EA888 Gen 3 & Gen 3B (1.8L & 2.0L TSI / TFSI CHHB / CJXC / CYFB)2015-2021
Audi S3 / A4 / Q5Volkswagen / Audi EA888 Gen 3 & Gen 3B (1.8L & 2.0L TSI / TFSI CHHB / CJXC / CYFB)2015-2023
04

Technical Specifications

SpecificationValue
System TypeVolkswagen Group EA888 Gen 3 200-bar FSI/TSI High-Pressure Fuel System
Operating PressureCore Spec
Pump MechanismCamshaft Multi-Lobe Actuated Single-Piston Plunger Pump
Mounting Flange Bolt Torque20 N·m (15 lb-ft) cross-pattern gradual clamping torque
Fuel Line Nut Torque27 N·m (20 lb-ft) high-pressure steel delivery pipe flare nut
Drive InterfaceRoller Tappet Lifter with Precision Hardened Roller
Flow Control SolenoidIntegrated 12V Pulse-Width Modulated Metering Valve
ManufacturerBosch (Tier-1 OEM for Volkswagen AG)
Bosch Production Number0261520197 / 0261520198

Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)

Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.

BOSCHExact Engine & Chassis Match
0261500162
Gasoline Direct Injection (GDI) • 200 bar
🚙 Engine Code CHHB
Technical Specifications & Pinout
BOSCHExact Engine & Chassis Match
06K906036G
Gasoline Direct Injection (GDI) • 200 bar
🚙 Engine Code CHHB
Technical Specifications & Pinout
BOSCHExact Engine & Chassis Match
06L906031A
Gasoline Direct Injection (GDI) • 200 bar
🚙 Engine Code CHHB
Technical Specifications & Pinout
BOSCHExact Engine & Chassis Match
06L906036AJ
Gasoline Direct Injection (GDI) • 200 bar
🚙 Engine Code CHHB
Technical Specifications & Pinout
CONTINENTALExact Engine & Chassis Match
06L906036K
High Pressure Injection System • 5 bar
🚙 Engine Code CHHB
Technical Specifications & Pinout
05

Installation Tips

  1. Low-Pressure Fuel Line Bleed & System Depressurization: Pull the low-pressure in-tank pump fuse. Crank engine until it stalls to deplete high-pressure fuel rail charge, then disconnect negative battery terminal.
  2. Intake Ducting & Electrical Disconnection: Unclip wiring harness from fuel pressure regulator valve N276. Disconnect low-pressure supply rubber hose by squeezing quick-release tabs with rag to catch residual fuel.
  3. High-Pressure Metal Fuel Delivery Pipe Removal: Counter-hold the pump outlet adapter with a 17mm wrench while unscrewing the 14mm pipe flare nut. Disconnect lower rail union and discard single-use pipe.
  4. Pump Flange Bolts Removal & Roller Tappet Inspection: Evenly loosen the two T30 Torx mounting bolts in half-turn increments to relieve spring tension. Remove pump and extract the roller lifter tappet from cylinder head bore to check for roller bearing play.
  5. New Pump Installation & Final Torque Sequence: Lubricate new Viton O-ring and roller tappet with fresh engine oil. Turn engine until cam is on base circle. Fasten mounting bolts evenly to 20 N·m (15 lb-ft) and steel line flare nut to 27 N·m (20 lb-ft).
Tips & Warnings:
  • Always install a fresh roller tappet: A worn or seized roller tappet will gouge the intake camshaft drive lobe, necessitating expensive cylinder head and camshaft replacement.
  • Verify engine oil for gasoline contamination: A failed internal shaft seal allows 200 bar fuel to spray directly into the cylinder head, diluting oil and risking rod bearing seizure.
  • Tighten mounting bolts evenly in stages: Drawing down one bolt first cocks the internal plunger against the bore, fracturing the mounting ears or binding the piston.
  • Cycle ignition to prime prior to start: Cycle key ON 3 times without cranking to pressurize the low-pressure feed circuit and bleed air from the pump chamber.
06

Frequently Asked Questions

QWill part 06K127025D fit my Volkswagen Golf or Audi S3/A4/Q5?

This 06K127025D gasoline direct-injection high-pressure fuel pump is listed for Volkswagen Golf (2015–2021) and Audi S3 / A4 / Q5 (2015–2023). It is also listed for the EA888 Gen 3 & Gen 3B 1.8L & 2.0L TSI / TFSI engine family with CHHB / CJXC / CYFB; confirm exact fitment by VIN against the vehicle’s EPC before ordering.

QWhat diagnostic trouble codes are listed for this high-pressure fuel pump?

The listing lists DTCs P0300, P0087, P0193, P0089, and P0191 for this gasoline direct-injection high-pressure fuel pump. The verified facts do not give symptom descriptions or a test procedure, so confirm the fault path against the vehicle’s service information.

QWhat are the system pressure and installation torque specs for this pump?

System pressure is listed as 200 bar, mounting / hold-down torque is 20 N·m, and high-pressure line torque is 27 N·m. Confirm any additional installation details against the vehicle’s repair information before fitting.

QCan I reuse the seals or does the pump need coding/adaptation, and how do I verify the old part?

The verified facts do not state seal reuse or coding/adaptation requirements for this pump, so confirm both against the vehicle’s EPC/service information rather than guessing. For identification, the pump is 06K127025D with cross references 06K127025, 06K127025J, 06K127025G, 261520197, and 261520198; verify the old unit and vehicle EPC before ordering.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0088Critical

Fuel Rail/System Pressure Too High

P0089Critical

Fuel Pressure Regulator 1 Performance

P0191Critical

Fuel Rail Pressure Sensor 'A' Circuit Range/Performance

P0002High

Fuel Volume Regulator Control Circuit Range / Performance (VCV / IMV)

P0090High

Fuel Pressure Regulator 1 Control Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

COMMON RAIL WORKSHOP DIAGNOSTICS

Common Rail High-Pressure Pump Diagnostics Guide

Diagnose common rail high-pressure pump failure: suction vacuum, CP4 roller glitter, plunger wear, air ingress & P0087 hard start. Workshop bench testing.

Read Technical Protocol
COMMON RAIL WORKSHOP DIAGNOSTICS

Fuel Metering Valve (IMV/SCV) Diagnostics Guide

Diagnostic guide for common rail fuel metering valves (IMV/SCV/FCA/MPROP). Normally open vs closed, coil resistance, PWM duty cycle & P0088 / P0089 test.

Read Technical Protocol
OBD-II DIAGNOSTIC PROTOCOL

P0087 Low Rail Pressure Diagnosis Guide

Step-by-step workshop diagnostic protocol for OBD-II DTC P0087 (Fuel Rail Pressure Too Low). 5-stage troubleshooting tree: backleak testing, SCV valve, PRV valve, and high-pressure pump.

Read Technical Protocol
COMMON RAIL WORKSHOP DIAGNOSTICS

Rail Pressure Relief Valve Diagnostics Guide

Common rail pressure relief valve (PRV) testing guide. Diagnose hot start stalls, P0087 rail pressure loss, return line leakage & single vs 2-stage valves.

Read Technical Protocol