BOSCH 06L127026A
High Pressure Fuel Pump Audi A4 B9 A5 Q5 VW Passat 2.0T EA888 Gen 3B 0261520474
0261520475, HPP0040, 0261520474--250 bar peak rail pressureProduct Overview
The 06L127026A is an original equipment (BOSCH) precision component engineered specifically for the Audi-Volkswagen 2.0L TFSI EA888 Gen 3B DOHC 16V I4 (CVKB / CYRB / DEMA / DKNA). Operating at peak injection pressures up to 250 bar (3625 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P0171, P2293.
Always verify the OE reference HPP0040 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 06L127026A needs no ECU calibration coding; no code transfer is required after fitting.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Volkswagen Golf Mk7/Mk7.5 | CHHB / CJXC / CYFB | 2013-2020 |
| Audi S3 (8V) / TTS (8S) | CHHB / CJXC / CYFB | 2014-2020 |
| Audi A4 (B9) / A5 (F5) / Q5 (FY) | CHHB / CJXC / CYFB | 2016-2021 |
| Porsche Macan | CHHB / CJXC / CYFB | 2015-2021 |
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 06L127026A |
| Manufacturer Brand | BOSCH |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Audi-Volkswagen 2.0L TFSI EA888 Gen 3B DOHC 16V I4 (CVKB / CYRB / DEMA / DKNA) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 20 N-m (15 lb-ft) |
| Fuel Line / Rail Torque | 27 N-m (20 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P0171, P2293 |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 20 N-m (15 lb-ft), and torque fuel line fittings to 27 N-m (20 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Verify the old pump part number and cross references 06L127026A, 0261520475, HPP0040, 0261520474, and 06L906036K before fitting.
- Tighten the mounting/hold-down fasteners to 20 N·m.
- Tighten the high-pressure line to 27 N·m.
Frequently Asked Questions
Will this 06L127026A pump fit my Volkswagen Golf Mk7 or Audi S3?
This 06L127026A pump is a gasoline direct-injection high-pressure fuel pump listed at 250 bar. It is listed for EA888 Gen 3 & Gen 3B 1.8L & 2.0L TSI/TFSI engines with codes CHHB, CJXC, and CYFB, including VW Golf Mk7/Mk7.5 (2013-2020), Audi S3 8V/TTS 8S (2014-2020), Audi A4 B9/A5 F5/Q5 FY (2016-2021), and Porsche Macan (2015-2021). Confirm fitment against the vehicle’s EPC by VIN before ordering.
What diagnostic trouble codes are associated with this high-pressure fuel pump listing?
The verified diagnostic trouble codes for this pump listing are P0300, P0087, P0193, P0089, and P0191. Confirm the actual fault with vehicle diagnostic data and service information; this listing does not state symptom descriptions.
Does this high-pressure fuel pump need coding or adaptation after installation?
No coding or adaptation procedure is stated in the verified facts. Confirm any coding/adaptation requirement against the vehicle’s EPC or manufacturer service information before installation.
Can I reuse the seals when installing this pump?
No seal-reuse specification is stated in the verified facts. Confirm seal and high-pressure line requirements against the vehicle’s EPC/service information; the verified mounting/hold-down torque is 20 N·m and high-pressure line torque is 27 N·m.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.