Delphi EJBR04401D
common rail injector
A6640170021, A6640170221, 664017002128239294L215PRD1600 bar peak rail pressureProduct Overview
The Delphi EJBR04401D is an authentic common rail diesel injector calibrated for SsangYong Kyron and D20DT engine applications. Operating at an engineered rail pressure of 1600 bar, this solenoid assembly features the precision 28239294 control valve and L215PRD nozzle. Mandatory ECU calibration requires programming the cylinder-specific C2i 16-digit hexadecimal code into the engine control unit to establish smooth delivery balance and Euro 4 emissions compliance. Typical failure symptoms include control valve erosion causing excessive back-leakage, rail pressure deficit (DTC P0087), and erratic cold-start idling. Overhauling necessitates clean room assembly and genuine replacement seals.
Verify Delphi C2i/C3i calibration code and OEM cross reference before installation.
Technical Specifications
| Specification | Value |
|---|---|
| SKU | EJBR04401D |
| Brand | DELPHI |
| Fuel System | Common Rail (Delphi DFI) |
| Operating PressureCore Spec | |
| Control ValveCore Spec | |
| Nozzle CodeCore Spec | |
| Hold Down Torque | 42 N·m |
| High-Pressure Line Torque | 40 N·m |
| Coding Required | Yes |
| Emission Standard | Euro 4 |
Installation Tips
- Depressurize And Clean: Depressurize the fuel system and isolate it according to the workshop procedure, then clean the surrounding area of the injector bore and the cylinder head before opening any connection.
- Disconnect Connections: Disconnect the electrical connector and the spill/return connection from the injector, then plug or cover all exposed ports and fittings to prevent dirt ingress.
- Remove High-Pressure Line: Remove the high-pressure line from the injector inlet, cap or plug the line and the injector port immediately, and keep the line ends clean.
- Extract Old Unit: Release and remove the hold-down device, extract the old injector from the bore, and remove any old seals without damaging the cylinder head or injector bore.
- Clean Bore And Seat: Clean the injector bore and seat in the cylinder head, remove carbon and debris, inspect the sealing surfaces, and keep the area covered until the new injector is ready.
- Fit Seals And Seat Unit: Fit new seals to the injector, seat the unit in the injector bore, tighten the hold-down to 42 N·m, then reconnect the high-pressure line and tighten it to 40 N·m; reconnect the electrical connector and spill connection.
- Calibration Coding: Record the 20-digit Delphi C2i/C3i calibration code and program it with a suitable diagnostic tool.
- Leak-Check And Start-Up: Leak-check the high-pressure line and injector connections, start the engine, and inspect for fuel leaks and abnormal running; stop the engine if any leak is found.
- Confirm the old injector part number against EJBR04401D or the listed cross references before ordering.
- Tighten the mounting/hold-down fasteners to 42 N·m.
- Tighten the high-pressure line to 40 N·m.
Frequently Asked Questions
Will this EJBR04401D injector fit my SsangYong Kyron or Actyon?
It is listed for SsangYong Kyron 2.0 XDi (D20DT) 2005-2015 and SsangYong Actyon I 2.0 XDi (D20DT) 2005-2012. For any other vehicle or engine variant, confirm fitment against the vehicle's EPC before ordering.
What diagnostic trouble codes can point to a problem with this injector?
The listed diagnostic trouble codes are P0300, P0087, P0201, P0204 and P0202. Use these codes as diagnostic evidence only and confirm the failed unit before replacement.
Does this injector need coding or adaptation after installation?
Coding or adaptation requirements are not stated in the verified facts, so they must be confirmed against the vehicle's EPC instead of guessed. Do not assume a coding procedure for the D20DT 2.0 XDi application.
How can I verify the old injector matches this listing?
Check the old unit's part number against EJBR04401D and the listed cross references: EJBR04901D, A6640170021, A6640170221 and 6640170021. If the number does not match or is unreadable, confirm the correct part against the vehicle's EPC before ordering.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.