095000-5880
Denso Toyota 2KD FTV Injector 23670 30050 Data
095000-5881, DCRI105880, 23670-30050, 23670-0L050, 23670-39185, 23670-09070, 23670-39215, 23670-39095, 23670-39096PLATE #02DLLA150P8661600 bar peak rail pressureProduct Overview
The Denso 095000-5880 (Toyota OE part numbers 23670-30050, 23670-0L050, 23670-39185, and aftermarket reference DCRI105880) is an electro-hydraulic common rail diesel fuel injector of the Denso G2 generation, engineered specifically for Toyota's 2.5-liter 2KD-FTV (D-4D 16V DOHC turbocharged) engine platform. Operating at peak rail injection pressures up to 1600 bar, this injector provides high-precision multi-stage pilot and main injections for Toyota Hilux pickups (KUN15/KUN25/KUN35), Hiace / Commuter commercial vans (KDH200 series), Fortuner SUVs, and Innova MPVs across global Euro 4 markets. Equipped with a micro-hole atomizing nozzle DLLA150P866 (093400-8660) and a matched hydraulic orifice control valve Plate #02, this injector delivers balanced fuel atomization for low NOx formation and stable cold-start combustion. After mechanical installation with a calibrated clamp bolt torque of 28 N·m, the laser-etched 30-digit Denso QR compensation code on the solenoid head must be calibrated into the engine ECM via Toyota Techstream or a high-end diagnostic scanner.
Always verify the OE reference 0950005881, DCRI105880, 2367030050, 236700L050 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 095000-5880 needs its calibration code transferred after fitting; read the code from the new unit and program it with a compatible diagnostic tool.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Toyota Hilux / Hiace / Fortuner | Toyota 2KD-FTV (2.5L D-4D DOHC 16V) | 2004-2015 |
Technical Specifications
| Specification | Value |
|---|---|
| INJECTOR TYPE | Common Rail Injector |
| SYSTEM PLATFORM | CRI |
| CONTROL VALVECore Spec | |
| NOZZLE CODECore Spec | |
| OPERATING PRESSURECore Spec |
Installation Tips
- Record QR Data: Before lowering the injector into the cylinder head, photograph or transcribe the 30-digit alphanumeric Denso QR code stamped on the plastic connector body.
- Clean Well & Seat: Use a brass seat-cleaning brush and industrial vacuum to remove all accumulated carbon deposits, fuel varnish, and debris from the cylinder head injector bore. Inspect the conical base for erosion.
- New Flame Washer: Always install a brand-new 1.5 mm copper seal washer (ID 7.7 mm / OD 15.0 mm) onto the nozzle tip. Never reuse old washers, as blow-by gases will overheat the nozzle spring and lead to permanent seizure.
- Injector Installation: Lightly coat the body O-ring with fresh engine oil. Slide the injector vertically into the bore until firmly seated by hand.
- Clamp Torquing: Fit the retaining clamp fork and torque the single clamp bolt strictly to 28 N·m (21 lb·ft). Do not over-torque, as over-tightening warps the internal valve body.
- High-Pressure Pipe: Hand-thread the fuel feed pipe flare nuts to ensure correct thread engagement, then torque to 32 N·m (24 lb·ft) with a 17 mm flare nut crowfoot.
- Fuel Return Banjo: Fit the spill rail return line with new aluminum sealing washers and torque the banjo bolts to 13 N·m (10 lb·ft).
- ECU Compensation Coding: Connect Toyota Techstream (GTS) or an equivalent professional scanner. Navigate to Engine -> Special Functions -> Injector Compensation Code and register each 30-digit code into its corresponding cylinder.
- Pilot Injection Quantity Learning: Warm the engine to operating coolant temperature (above 80°C / 176°F), turn off all electrical loads (A/C, lights, demister), and trigger the automatic Pilot Quantity Learning routine to adapt rail pressure variations.
- Confirm the exact vehicle/engine against the EPC before ordering part 095000-5880.
- Tighten the mounting/hold-down to 28 N·m and the high-pressure line to 32 N·m.
- Verify coding/adaptation, seal reuse, and expected service life against the vehicle’s EPC instead of guessing.
Frequently Asked Questions
Will part 095000-5880 fit my Toyota Hilux, Hiace, or Fortuner?
It is listed as a common-rail diesel injector for the Toyota 2KD-FTV (2.5L D-4D DOHC 16V) in Toyota Hilux, Hiace, and Fortuner applications from 2004-2015. Cross references include 0950005880, 0950005881, DCRI105880, 2367030050, 236700L050, and 2367039185; confirm the exact vehicle/engine against the EPC before fitment.
What diagnostic trouble codes are listed for this injector?
The verified diagnostic trouble codes for this listing are P0300, P0301, P0087, P0302, and P0304. Use them as listed diagnostic references and confirm the diagnosis against the vehicle's EPC rather than guessing.
Does this injector require coding or adaptation?
The verified facts do not state coding or adaptation requirements for part 095000-5880. Confirm the requirement against the vehicle's EPC rather than guessing.
What mounting, high-pressure line, and system pressure values are specified?
Mounting/hold-down torque is 28 N·m, and high-pressure line torque is 32 N·m. The common-rail system pressure is listed as 1600 bar.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.