095000-5890
Denso Komatsu PC300 8 Injector 6251 11 3200 Data
095000-5891, 095000-5892, DCRI105890, 6251-11-3200, 6251-11-3201, 6251-11-3202PLATE #10DLLA152P9891600 bar peak rail pressureProduct Overview
The Denso 095000-5890 (Komatsu genuine OE part numbers 6251-11-3200, 6251-11-3201, 6251-11-3202, and aftermarket reference DCRI105890) is an industrial heavy-duty common rail diesel fuel injector from the Denso G2 platform. Engineered specifically for Komatsu's 8.3-liter, 6-cylinder SAA6D114E-3 electronic turbocharged diesel engines, it complies with EPA Tier 3 and EU Stage IIIA off-highway non-road emissions standards. Operating at peak injection pressures up to 1600 bar, this injector delivers multi-stage high-pressure fuel metering for world-class heavy earthmoving machines, including Komatsu PC300-8, PC300LC-8, PC350-8, and PC350LC-8 hydraulic crawler excavators, WA380-6 wheel loaders, and D65-15 track-type bulldozers. The internal hydraulic assembly features a high-precision multi-hole spray nozzle DLLA152P989 (093400-9890) driven by a precision spool valve Plate #10 (095000-0100). Due to the cylinder head's internal side-entry fuel delivery geometry, correct installation requires adhering to strict sequential tightening specifications between the injector hold-down clamp and the side fuel connector quill tube to prevent pressurized diesel from leaking into the crankcase lubricating oil.
Always verify the OE reference 0950005891, 0950005892, DCRI105890, 6251113200 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 095000-5890 needs its calibration code transferred after fitting; read the code from the new unit and program it with a compatible diagnostic tool.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Komatsu PC300-8 / PC350-8 | Cummins QSL9 / ISLe 8.9L & Komatsu SAA6D114E-3 (8.9L) | 2006-2020 |
Technical Specifications
| Specification | Value |
|---|---|
| INJECTOR TYPE | Common Rail Injector |
| SYSTEM PLATFORM | CRI |
| CONTROL VALVECore Spec | 🔗 Shared Valve (2 assemblies):095000-6070 |
| NOZZLE CODECore Spec | |
| OPERATING PRESSURECore Spec |
Installation Tips
- Bore Inspection & Cleaning: Clean the injector bore sleeve thoroughly using brass wire cleaning brushes and vacuum extraction. Inspect the sealing seat at the bottom of the bore with a borescope; verify it is free from residual carbon, pitting, or old copper fragments.
- Washer & Injector Installation: Slide a brand-new 1.5 mm copper crush washer (6215-11-3940) onto the injector nozzle shank. Lower the injector vertically into the cylinder head bore and press firmly by hand until seated. Install the hold-down clamp and finger-tighten the clamp bolt.
- Quill Tube Hand Alignment: Insert the side connector tube through the cylinder head port into the injector inlet seat. Thread the connector retaining nut by hand until snug against the seat. Do NOT tighten with a wrench yet.
- Injector Clamp Pre-Torquing: Torque the injector clamp hold-down bolt to an initial pre-torque of 15 N·m (prior to final 34 N·m) to draw the injector body into axial vertical alignment.
- Connector Retaining Nut Initial Torque: Torque the connector tube retaining nut to 25 N·m to seat the spherical nose cone into the injector inlet socket.
- Final Clamp Torquing: Tighten the injector hold-down clamp bolt to its full workshop specification of 34 N·m.
- Final Connector Retaining Nut Torquing: Finalize tightening the fuel connector tube retaining nut to 50 N·m.
- Fuel Delivery Line Torquing: Install the high-pressure steel fuel line from the common rail to the connector tube fitting and tighten both flare nuts to 35 N·m.
- Verify part number 095000-5890 or cross references 0950005890, 0950005891, 0950005892, DCRI105890, 6251113200, or 6251113201 on the common-rail diesel injector before replacement.
- Tighten the mounting/hold-down torque to 34 N·m and the high-pressure line torque to 34 N·m.
- Confirm fitment for Cummins QSL9 / ISLe 8.9L and Komatsu SAA6D114E-3 (8.9L) in Komatsu PC300-8 / PC350-8 (2006-2020) before installation.
Frequently Asked Questions
Which Komatsu heavy mining excavators and engines use Denso injector 095000-5890?
Denso 095000-5890 is calibrated for Komatsu SAA6D114E-3 (8.27L, 6-cylinder Tier 3) industrial diesel engines. It is standard equipment on Komatsu PC300-8, PC300LC-8, PC350-8, PC350LC-8 hydraulic excavators, WA380-6 wheel loaders, and D65EX-15 / D65PX-15 bulldozers from 2006 to 2018.
What are the Komatsu OEM reference part numbers for Denso 095000-5890?
Genuine Komatsu OE numbers are 6251-11-3200, 6251-11-3201, and 6251-11-3202, with aftermarket reference DCRI105890. It belongs to the heavy-duty Denso G2 common rail architecture.
How is Denso 095000-5890 registered in the Komatsu PC300-8 engine controller?
Input the 30-digit QR compensation code stamped on the top connector into the engine controller via Komatsu K-Doc diagnostic software. This registers the manufacturing flow rate curve and prevents cylinder-to-cylinder fuel balance errors.
What is the clamp bolt tightening torque for Komatsu SAA6D114E-3 injectors?
Torque the injector hold-down clamp bolt to 34 N·m. Always clean the cylinder head bore thoroughly, seat a new 1.5 mm heat-treated copper washer, and lubricate the injector body O-ring before lowering the injector into place.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.