BOSCH BL3Z-9F593-B
Direct Fuel Injector Ford F 150 Transit Expedition Lincoln Navigator 3.5L EcoBoost 0261500105
BL3E-9F593-BA, 0261500105, FJ1117, CM5214--150 bar peak rail pressureProduct Overview
The BOSCH BL3Z-9F593-B is a factory precision fuel injection component engineered specifically for the Ford 3.5L EcoBoost Twin-Turbo DOHC 24V V6. Manufactured to strict original equipment tolerances, it delivers precise fuel atomization and operates up to its rated pressure of 150 bar (2175 psi). Common operational failure symptoms that point directly to this assembly include: Persistent Diagnostic Trouble Codes such as P0300, P0301, P0302, P0303 stored in the ECM. Hard cold starting, erratic idle oscillations, and severe acceleration stumbling. Unburnt fuel smell in the exhaust, black tailpipe soot, or fuel dilution in the engine crankcase. Loss of high-RPM power and engine protection limp-mode activation under highway load.
Always verify the OE reference BL3E9F593BA, FJ1117, CM5214 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. BL3Z-9F593-B needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| sku | BL3Z-9F593-B |
| brand | BOSCH |
| manufacturer_code | 0261500105 |
| pressure_rating | 150 bar (2175 psi) |
| torque_flange | 10 N-m (89 lb-in) |
| torque_line | 20 N-m (15 lb-ft) |
| engine_family | Ford 3.5L EcoBoost Twin-Turbo DOHC 24V V6 |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Always replace single-use high-pressure fuel lines and Teflon/copper sealing washers before installation.
- Lubricate the pump roller tappet or injector O-rings with clean engine oil before guiding into place.
- Tighten mounting flange fasteners in an even criss-cross pattern to 10 N-m (89 lb-in).
- Hand-thread fuel rail fittings first, then torque high-pressure flare nuts to 20 N-m (15 lb-ft) using a calibrated crowfoot wrench.
- Cycle the low-pressure fuel pump multiple times and perform a physical leak inspection before engine ignition.
- Verify the replacement injector is BL3Z-9F593-B or a listed cross reference before installation.
- Torque the injector hold-down to 10 N·m and the high-pressure line to 20 N·m.
- Confirm seal reuse, coding/adaptation, and any service-life guidance against the vehicle's EPC instead of guessing.
Frequently Asked Questions
Will this fit my Ford 3.5L EcoBoost vehicle?
This gasoline direct-injection injector, part number BL3Z-9F593-B, is listed for a 150 bar system and the Ford 3.5L V6 EcoBoost Twin-Turbo Gen 1 & Gen 2 D35. Fitment includes Ford F-150 3.5 EcoBoost D35 (2011-2020), Ford Expedition 3.5 EcoBoost D35 (2015-2021), and Lincoln Navigator 3.5 EcoBoost D35 (2015-2021). Confirm against the vehicle's EPC.
What diagnostic trouble codes are listed for this injector?
The diagnostic trouble codes listed for this injector are P0300, P0301, P0087, P0302, and P0304. Use them as diagnostic leads and confirm the cause rather than replacing parts on codes alone.
Does this injector need coding or adaptation after installation?
No coding or adaptation requirement is stated in the supplied facts for this injector. Confirm any required procedure against the vehicle's EPC/service information before installation.
How do I verify the old injector part number?
Compare the old unit’s markings to BL3Z-9F593-B and the listed cross references: BL3Z9F593B, BL3E9F593BA, 0261500105, FJ1117, CM5214, BB5Z9350A. If the markings are unclear or do not match, confirm fitment against the vehicle's EPC.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.