BOSCH HL3Z-9F593-B
Direct Fuel Injector Ford F 150 Raptor Expedition Lincoln Navigator 3.5L EcoBoost 0261500363
HL3E-9F593-BB, FJ1283, 0261500363--200 bar peak rail pressureProduct Overview
The HL3Z-9F593-B is an original equipment (BOSCH) precision component engineered specifically for the Ford 3.5L EcoBoost Twin-Turbo V6 Gen 2 Dual-Injection (D35). Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0300, P0301, P0172, P0175.
Always verify the OE reference HL3E9F593BB, FJ1283 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. HL3Z-9F593-B needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | HL3Z-9F593-B |
| Manufacturer Brand | BOSCH |
| Component Type | Direct Fuel Injector |
| Engine Application | Ford 3.5L EcoBoost Twin-Turbo V6 Gen 2 Dual-Injection (D35) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 10 N-m (89 lb-in) |
| Fuel Line / Rail Torque | 20 N-m (15 lb-ft) |
| Primary Diagnostic Fault Codes | P0300, P0301, P0172, P0175 |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 10 N-m (89 lb-in), and torque fuel line fittings to 20 N-m (15 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Before installation, verify the replacement injector part number HL3Z-9F593-B against the vehicle EPC using the VIN.
- Inspect the injector connector and sealing surfaces, and confirm any coding or adaptation steps in the workshop manual.
- Handle the injector carefully and keep it clean during removal and installation to avoid contamination.
Frequently Asked Questions
Will this fit my Ford EcoBoost vehicle?
HL3Z-9F593-B is listed for the Ford pickup, Expedition, and Lincoln Navigator EcoBoost applications shown in fitment; confirm your exact vehicle against the EPC or workshop manual before ordering.
What should I check before ordering?
Check the VIN, EPC fitment, connector and seal condition, and whether coding or adaptation is required in the workshop manual; the listing does not state those requirements for HL3Z-9F593-B.
Does the old injector need to be matched or adapted?
The listing does not state coding or adaptation requirements; confirm injector matching or adaptation for the vehicle against the EPC or workshop manual before installing HL3Z-9F593-B.
What are the symptoms of a failed injector?
The listing does not specify failure symptoms; use the vehicle workshop manual to diagnose driveability or fueling complaints and confirm HL3Z-9F593-B fits the exact application before replacement.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.