BOSCH BM5G-9F593-BA
Fuel Injector Ford Fiesta ST Fusion Escape 1.6L EcoBoost CM5Z 9F593 A 0261500155
CM5Z-9F593-A, 0261500155, 0261500156, FJ1170, 31336688BOSCH HDEV5 SOLENOID VALVE ACTUATOR6-Hole Precision Direct-Injection Atomization Nozzle150 bar peak rail pressureProduct Overview
The Bosch BM5G-9F593-BA (Bosch production part numbers 0261500155 and 0261500156, Ford service reference CM5Z-9F593-A, and Volvo reference 31336688) is the authentic original equipment high-pressure solenoid gasoline direct injection (GDI) fuel injector developed for Ford's popular 1.6-liter EcoBoost turbocharged 4-cylinder engine platform. Operating at pressures up to 150 bar (2,175 psi), this Bosch HDEV5 high-speed injector is factory equipment on the spirited Ford Fiesta ST (2014-2019), Ford Escape 1.6L (2013-2016), Ford Fusion (2013-2014), Ford Focus 1.6 EcoBoost, and Volvo S60/V60 T3 and T4 models.
Always verify the original manufacturer reference stamped on your component before ordering. For BM5G-9F593-BA, inspect matching OE cross-references and ensure related high-pressure seals, followers, or grommets are renewed during service.
Technical Specifications
| Specification | Value |
|---|---|
| System Type | Bosch HDEV5 High-Pressure Solenoid Direct Injection |
| Maximum Operating Rail PressureCore Spec | |
| Solenoid Coil Resistance | 1.5 - 2.5 Ohms @ 20°C (Low-Impedance Peak-and-Hold GDI Drive) |
| Spray Pattern | 6-Hole Multi-Directional Asymmetric Cone Spray Pattern |
| Fuel Rail Mounting Bolts Torque | 20 N·m (15 lb-ft) tightened evenly to engine cylinder head |
| Injector Retaining Clip Fastener | 10 N·m (89 in-lb) hold-down clamp securing injectors in head |
| Combustion Chamber Seal | Virgin Solid PTFE Teflon Seal Ring (Requires Sizing Tool) |
| Fuel Rail Upper Seal | Viton High-Pressure Fluorocarbon O-Ring |
| Manufacturer | Robert Bosch GmbH (Tier-1 OEM for Ford Motor Company & Volvo) |
| Production Reference | Bosch 0261500155 / Ford BM5G-9F593-BA |
| Operating PressureCore Spec |
Installation Tips
- High-Pressure Direct Injection Line Depressurization: Remove low-pressure fuel pump fuse in passenger cabin. Crank engine until it stalls to purge residual rail pressure. Disconnect negative battery ground cable before starting disassembly.
- Intake Manifold & Wiring Harness Clearance: Unbolt upper intake plenum, throttle body ducting, and PCV hose assembly. Unclip the main fuel injector wiring harness connectors from all four GDI injectors.
- High-Pressure Fuel Rail & Retaining Clip Removal: Unscrew the high-pressure fuel supply pipe fitting. Remove the fuel rail mounting bolts and gently withdraw the aluminum fuel rail assembly together with the injectors from the cylinder head.
- Combustion Chamber Bore Cleaning & Teflon Seal Replacement: Clean injector combustion bores with dedicated brass cleaning brushes. If installing new injectors, verify protective plastic covers are intact; if resealing, use specialized pilot sizing cones to install new virgin PTFE Teflon seals.
- Injector Installation, Rail Alignment & Specified Torquing: Push injectors into fuel rail pockets and align into cylinder head bores. Torque fuel rail mounting bolts to 20 N·m (15 lb-ft) and injector hold-down clips to 10 N·m (89 in-lb). Reassemble intake manifold.
- Confirm part number BM5G-9F593-BA and the listed cross references against the vehicle’s EPC before installation.
- Tighten the injector mounting/hold-down to 10 N·m and the high-pressure line to 20 N·m.
- Treat P0300, P0301, P0087, P0302, and P0304 as diagnostic leads, not proof that the injector has failed.
Frequently Asked Questions
Will this injector fit a Ford Fiesta ST in the listed 2014–2019 application?
It is listed for Ford Fiesta ST with engine codes JTJA, JTMA, JTBA, and B4164T (2014–2019), plus Ford Escape/Kuga (2013–2016), Ford Fusion/Mondeo Mk5 (2013–2014), and Volvo S60/V60 (2011–2015) with those engine codes. Verify the old unit against part number BM5G-9F593-BA or the listed cross references BM5G9F593BA, CM5Z9F593A, 0261500155, 0261500156, FJ1170, and 31336688. If the vehicle’s EPC does not confirm the application, do not guess.
What symptoms or trouble codes are associated with this injector listing?
The listing provides diagnostic trouble codes P0300, P0301, P0087, P0302, and P0304, but it does not state a symptom list. Use these codes as diagnostic leads and confirm the fault properly rather than replacing the injector on codes alone.
Does this injector require coding or adaptation after installation?
Coding or adaptation requirements are not stated in the verified facts, so they must be confirmed against the vehicle’s EPC instead of guessing. Do not assume coding is unnecessary.
What torques apply, and can I reuse the seals?
The listed system pressure is 150 bar, the mounting/hold-down torque is 10 N·m, and the high-pressure line torque is 20 N·m. Seal reuse is not stated in the verified facts, so it must be confirmed against the vehicle’s EPC instead of guessing.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.