BOSCH DL3Z-9F593-A
High Pressure Direct Fuel Injector Ford F 150 Expedition Transit Lincoln Navigator 3.5L EcoBoost V6 0261500140
0261500140, 0261500141, FJ1151HIGH-RESPONSE MULTI-HOLE ELECTROMAGNETIC HIGH-PRESSURE NOZZLE-150 bar peak rail pressureProduct Overview
The Bosch DL3Z-9F593-A (Bosch part number 0261500140, replacing prior revisions BL3Z-9F593-B) is the original equipment high-pressure gasoline direct injection injector engineered for Ford's flagship 3.5-liter EcoBoost Twin-Turbo V6 engine. Employed across high-volume platforms such as the Ford F-150, Expedition, Transit commercial vans, and Lincoln Navigator, this 150-bar (2175 psi) electromagnetic injector atomizes fuel directly into the combustion chamber to deliver maximum torque and fuel efficiency under severe towing loads. Common drivability complaints reported by EcoBoost truck owners include intermittent catalytic-converter shudder under boost, heavy black exhaust smoke on cold start, and diagnostic trouble codes P0300 (Random Misfire), P0301 through P0306 (Cylinder 1-6 Misfire), and P0172 / P0175 (System Too Rich Bank 1 / Bank 2). These conditions frequently arise from micro-droplet leakage past internal needle seats when thermal cycling and carbon build-up cause the injector pintle to stick open during engine shutdown. Correct replacement requires strict adherence to clean-room practices. Fuel rail retaining bolts must be torqued to 10 N·m (89 in-lb) in alternating sequence, and high-pressure fuel pipe union flare nuts tightened to 28 N·m (21 lb-ft). Technicians should always replace spark plugs and engine oil if significant fuel wash has occurred to safeguard turbocharger bearings and piston rings.
Always verify the OE reference FJ1151 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. DL3Z-9F593-A needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| System Type | Ford EcoBoost 150-bar High-Pressure Direct Injection System |
| Operating PressureCore Spec | |
| Spray Configuration | Laser-Drilled 6-Hole Asymmetric Spray Pattern |
| Injector Hold-Down Bolt Torque | 10 N·m (89 in-lb) fuel rail mounting bolts📐 Torque & Angle Wizard → |
| Fuel Line Nut Torque | 28 N·m (21 lb-ft) high-pressure crossover tube flare nut |
| Combustion Seal | PTFE Virgin Teflon Combustion Ring with Backing Washer |
| Rail Sealing | High-Temperature Fluorocarbon (FKM) Upper O-Ring |
| Manufacturer | Bosch (Tier-1 OEM for Ford Motor Company) |
| Bosch Production Number | 0261500140 / 0261500141 |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- EcoBoost High-Pressure Fuel Rail Depressurization: Depressurize fuel system by removing the low-pressure fuel pump fuse and running engine until it dies. Disconnect negative battery cable.
- Upper Intake Manifold & Charge Pipes Removal: Disconnect turbo boost pipes, throttle body wiring, PCV hoses, and remove the composite upper intake plenum to access Bank 1 and Bank 2 fuel rails.
- High-Pressure Crossover Pipe Disconnection: Unscrew the stainless steel high-pressure fuel crossover lines using a 17mm flare nut wrench. Discard the single-use hard pipes per Ford service directives.
- Fuel Rail Extraction & Bore Prep: Remove fuel rail retaining bolts. Pull rails and injectors straight back along their axis. Thoroughly clean carbon deposits from the cylinder head injector wells.
- Injector Installation & Final Torquing: Lubricate upper O-rings with clean engine oil (keep Teflon tips completely dry). Push injectors into rail, torque rail bolts to 10 N·m (89 in-lb), and crossover pipe nuts to 28 N·m (21 lb-ft).
- Observe the specified 150 bar system pressure for this gasoline direct-injection injector.
- Tighten the mounting/hold-down to 10 N·m.
- Tighten the high-pressure line to 28 N·m.
Frequently Asked Questions
Will this injector fit my vehicle?
This DL3Z-9F593-A gasoline direct-injection injector is listed for the Ford 3.5L V6 EcoBoost Twin-Turbo (Gen 1 & Gen 2 D35). It fits Ford F-150 D35 (2011-2020), Ford Expedition D35 (2015-2024), and Lincoln Navigator D35 (2015-2024). Confirm fitment against the vehicle's EPC before ordering.
Which diagnostic trouble codes are listed for this injector?
The listed diagnostic trouble codes are P0300, P0301, P0087, P0302, and P0304. Any additional symptom or root-cause diagnosis must be confirmed against the vehicle's EPC instead of guessing.
Does this injector require coding or adaptation?
Coding or adaptation requirements are not stated in the verified facts. Confirm this against the vehicle's EPC instead of guessing.
How can I verify the old injector part?
Check for part number DL3Z-9F593-A and compare it with the listed cross references: DL3Z9F593A, 0261500140, 0261500141, FJ1151, 0261500162, and 06E906036E. If the marking is unclear, confirm against the vehicle's EPC.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.