Catalog / BOSCH / CM5E-9F593-BB
BOSCH

BOSCH CM5E-9F593-BB

View Specs
SolenoidGasoline Direct Injection (GDI / HDEV)Euro 5

High Pressure Direct Fuel Injector Ford Focus 2.0L GDI Ti VCT Escape 2.0L Duratec CM5Z 9F593 B 0261500073

Reference data for BOSCH CM5E-9F593-BB common rail injector · OEM CM5Z-9F593-B, 0261500073, 0261500074, FJ1151 · Application Ford 2.0L Duratec 20 GDI Ti-VCT DOHC 16-Valve Inline-4 Naturally Aspirated
OE REFERENCECM5Z-9F593-B, 0261500073, 0261500074, FJ1151
CONTROL VALVEHIGH-RESPONSE MULTI-HOLE ELECTROMAGNETIC DIRECT INJECTION NOZZLE
NOZZLE-
EMISSIONEuro 5
WARRANTY12 Months
01

Product Overview

The Bosch CM5E-9F593-BB (Ford OE reference CM5Z-9F593-B, Bosch engineering number 0261500073, alternate revision 0261500074) is the original equipment high-pressure direct fuel injector (GDI) engineered for Ford's naturally aspirated 2.0-liter Duratec Ti-VCT engine. Operating at pressures up to 150 bar (2175 psi), this multi-hole solenoid injector delivers high-velocity atomization for the global third-generation Ford Focus (2012-2018) and Ford Escape utility models. Due to direct exposure inside the combustion chamber, microscopic laser-drilled spray orifices frequently suffer from severe carbon and gum buildup. Drivers commonly experience rough cold starts, engine hesitation under acceleration, check engine light illumination, and diagnostic trouble codes P0300 (Random Cylinder Misfire), specific cylinder misfires (P0301, P0302, P0303, P0304), and lean fuel trim codes P0171 (System Too Lean Bank 1). Worn internal needle valve seats can also allow unmetered fuel to seep into the cylinder during hot soak, causing difficult hot restarts. Correct installation demands strict workshop compliance. Technicians must clean carbon from cylinder head injector bores and size virgin PTFE combustion seals using specialized calibration cones. Rail mounting bolts must be drawn down evenly to 10 N·m (89 in-lb), while the high-pressure steel supply pipe union nut requires 28 N·m (21 lb-ft). High-pressure leak testing must confirm absolute seal integrity before reinstalling the intake manifold.

Before You Order

Always verify the OE reference CM5Z9F593B, FJ1151 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. CM5E-9F593-BB needs no ECU calibration coding; no code transfer is required after fitting.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Ford Focus Mk3Ford 2.0L Duratec 20 GDI Ti-VCT DOHC 16-Valve Inline-4 Naturally Aspirated2012-2018
Ford Transit ConnectFord 2.0L Duratec 20 GDI Ti-VCT DOHC 16-Valve Inline-4 Naturally Aspirated2019-2023
04

Technical Specifications

SpecificationValue
System TypeFord GDI 150-bar High-Pressure Direct Fuel Injection System
Operating PressureCore Spec
Spray GeometryHigh-Pressure Laser Multi-Hole Asymmetric Dispersion Pattern
Injector Hold-Down Fastener Torque10 N·m (89 in-lb) fuel rail mounting bolts📐 Torque & Angle Wizard →
Fuel Feed Pipe Nut Torque28 N·m (21 lb-ft) high-pressure supply line union
Combustion SealHigh-Density Sintered Virgin PTFE Teflon Combustion Ring
Upper Rail O-RingFluorocarbon (FKM) High-Temp Viton Rail Seal
ManufacturerBosch (Tier-1 OEM for Ford Motor Company)
Bosch Production Reference0261500073 / 0261500074
05

Installation Tips

  1. GDI High-Pressure Fuel Circuit Depressurization: Remove fuel pump fuse (Fuse F56 or F22) in passenger compartment fuse box. Crank engine until it stalls to bleed pressure, then disconnect negative battery terminal.
  2. Intake Manifold & Vacuum Line Disconnection: Unbolt upper intake plenum, detach PCV hoses and EVAP purge lines, and disconnect throttle body harness to access the fuel rail mounted in the cylinder head.
  3. Rigid High-Pressure Fuel Supply Pipe Removal: Loosen high-pressure metal fuel supply line union nuts with a 17mm flare wrench. Discard single-use flared pipe per Ford OEM workshop service directives.
  4. Fuel Rail Extraction & Cylinder Head Bore Cleaning: Remove fuel rail retaining bolts. Pull rail and injectors straight out using an injector slide hammer puller if seized with carbon. Clean combustion carbon from head bores.
  5. New PTFE Seal Installation, Insertion & Torquing: Size new Teflon combustion seal with sizing cone tool. Lubricate upper Viton O-rings with clean engine oil. Torque rail retaining bolts to 10 N·m (89 in-lb) and metal line nut to 28 N·m (21 lb-ft).
Tips & Warnings:
  • Never install PTFE combustion seal dry without sizing: Use specialized expansion and sizing collars; a distorted Teflon ring tears upon cylinder head insertion, causing compression blow-by.
  • Mandatory high-pressure fuel line replacement: Ford factory service manuals mandate replacement of the rigid steel line whenever flare fittings are loosened.
  • Clean cylinder head injector bores thoroughly: Carbon deposits in the cylinder head bore cause improper seating, improper spray angle, and poor thermal dissipation.
  • Inspect spark plugs for fouling: A dripping direct injector fouls the spark plug electrode; replace plugs if carbon crusted or fuel soaked.
06

Frequently Asked Questions

QWill this injector fit my Ford Focus Mk3 or Transit Connect?

This gasoline direct-injection injector, part number CM5E-9F593-BB, is listed for Ford Focus Mk3 (2012-2018) and Ford Transit Connect (2019-2023). It is listed for the Ford 2.0L Duratec 20 GDI Ti-VCT DOHC 16-Valve Inline-4 Naturally Aspirated engine family. Confirm fitment by VIN/EPC before ordering.

QWhat symptoms or trouble codes point to a failed injector?

The diagnostic trouble codes listed for this part are P0300, P0301, P0087, P0302, and P0304. This listing does not state other symptom details, so use these codes as the listed diagnostic references and confirm the fault before replacement.

QCan I reuse the seals and do I need to code or adapt the injector?

The listing does not state seal-reuse or coding/adaptation requirements, so those must be confirmed against the vehicle’s EPC or service information rather than assumed. Mounting / hold-down torque is 10 N·m, and high-pressure line torque is 28 N·m for this injector. System pressure is 150 bar.

QHow can I verify the old part and cross-reference it?

Check the old injector for part number CM5E-9F593-BB and compare it against cross references CM5E9F593BB, CM5Z9F593B, 0261500073, 0261500074, FJ1151, and 16611AA720. This is a gasoline direct-injection injector for the listed Ford engine family and fitments. If the markings are unclear, confirm fitment against the vehicle’s EPC.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0200Critical

Fuel Injector Circuit Malfunction (General / Common Driver Stage)

P0201Critical

Injector Circuit Malfunction - Cylinder 1

P0300Critical

Random or Multiple Cylinder Misfire Detected

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

COMMON RAIL WORKSHOP DIAGNOSTICS

Fuel Metering Valve (IMV/SCV) Diagnostics Guide

Diagnostic guide for common rail fuel metering valves (IMV/SCV/FCA/MPROP). Normally open vs closed, coil resistance, PWM duty cycle & P0088 / P0089 test.

Read Technical Protocol
OBD-II DIAGNOSTIC PROTOCOL

P0087 Low Rail Pressure Diagnosis Guide

Step-by-step workshop diagnostic protocol for OBD-II DTC P0087 (Fuel Rail Pressure Too Low). 5-stage troubleshooting tree: backleak testing, SCV valve, PRV valve, and high-pressure pump.

Read Technical Protocol
DIESEL WORKSHOP DIAGNOSTIC SOP

Cylinder Balance & Injector Deviation Guide

Common rail diesel cylinder balance & smooth running diagnostic guide. Balance rates, mg/stroke deviation, P0263 misfire, compression vs injector test.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol