GM 12698485
High Pressure Fuel Pump Chevrolet Silverado Tahoe GMC Sierra Yukon 5.3L L84 6.2L L87 DFM
12688609, GDP110, HPP0049--200 bar peak rail pressureProduct Overview
The 12698485 is an original equipment (GM) precision component engineered specifically for the General Motors EcoTec3 Gen V 5.3L (L84) & 6.2L (L87) V8 with Dynamic Fuel Management (DFM). Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P0171, P053F.
Always verify the OE reference 12688609, GDP110, HPP0049 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 12698485 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 12698485 |
| Manufacturer Brand | GM |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | General Motors EcoTec3 Gen V 5.3L (L84) & 6.2L (L87) V8 with Dynamic Fuel Management (DFM) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 15 N-m (133 lb-in) |
| Fuel Line / Rail Torque | 30 N-m (22 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P0171, P053F |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 15 N-m (133 lb-in), and torque fuel line fittings to 30 N-m (22 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Clean the high-pressure fuel lines and fittings before opening the system, and cap open ports to prevent contamination.
- Confirm the part number 12698485 and the vehicle application against the EPC before installation.
- After fitting, check for leaks and verify pressurization using the vehicle's workshop procedure.
Frequently Asked Questions
Will this pump fit my vehicle?
It is listed for Chevrolet Silverado, Tahoe, Suburban and GMC Sierra, Yukon applications using the GM Gen V gasoline direct-injection engine family; verify your VIN and engine against the vehicle's EPC before ordering.
What symptoms suggest the high-pressure fuel pump has failed?
Look for extended cranking, hesitation or power loss under load, fuel-pressure-related codes, and a gasoline smell; confirm pressure and diagnosis with the vehicle's workshop data before replacing.
What should I check before ordering?
Confirm the part number 12698485, verify VIN and engine application against the vehicle's EPC, inspect connectors and fuel lines, and rule out low-side supply or control-circuit faults with workshop diagnostics.
Does the replacement pump need coding or matching?
Coding or adaptation requirements are not stated here; confirm them against the vehicle's EPC or workshop manual. Also check seal and fastener reuse guidance there before installation.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.