BOSCH 12698552
High Pressure Fuel Injector Cadillac CT4 CT5 XT4 Buick Envision 2.0T LSY Ecotec 0261500690
12707255, 0261500690, 0261500691HIGH-PRESSURE SOLENOID MULTI-HOLE INJECTOR NOZZLE-350 bar peak rail pressureProduct Overview
The Bosch 12698552 (Bosch 0261500690) is a Bosch HDEV6 350-bar high-pressure direct gasoline injector for GM 2.0L Ecotec turbo SIDI engines (LTG / LSY Tripower / LHU). Applications include the Cadillac CT5 (2020-2024), XT4 (2019-2024) and Buick Envision II (2021-2024). Rated maximum rail pressure is 350 bar (35 MPa / 5075 psi), with an advanced multi-hole laser-drilled atomizing pattern for Tripower cam profiles and coil resistance of 1.4-1.8 Ω at 20°C. Holding bracket retaining bolts are specified at 10 N·m and the high-pressure pipe flare nut at 28 N·m. Common codes are P0300, P0301-P0304 and P0171. New Teflon sealing rings must be sized with the GM pilot tool; the seals are not reusable.
Always verify the OE reference 12707255 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 12698552 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| System Type | Bosch HDEV6 350-bar High-Pressure Direct Gasoline Injector |
| Operating PressureCore Spec | |
| Spray Pattern | Advanced multi-hole laser-drilled atomizing pattern for Tripower cam profiles |
| Fuel Rail Bolt Torque | 10 N·m (holding bracket retaining bolts) |
| High Pressure Pipe Torque | 28 N·m Flare Nut Connection |
| Coil Resistance | 1.4 - 1.8 Ω at 20°C (High-voltage peak-and-hold driver circuit) |
| Common Fault Codes | P0300 (Random Misfire), P0301-P0304 (Cylinder Misfire), P0171 (System Lean Bank 1) |
| Workshop Precaution | Install new Teflon sealing rings using GM pilot tool; never reuse Teflon combustion seals |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Depressurize 350-bar Fuel System & Disconnect Battery: Depressurize high pressure fuel rail via diagnostic scan tool or fuel pump relay isolation. Disconnect battery 12V negative terminal.
- Remove Upper Intake Ducting & Fuel Rail Shielding: Remove charge air piping and acoustic foam insulator. Loosen the high pressure steel fuel rail line (28 N·m) with backup counter-wrench.
- Extract Injectors & Fit New Teflon Sealing Rings: Use GM injector puller tool EN-47277 to withdraw injectors. Install replacement Teflon combustion seals using expander and compression guide.
- Torque Rail Fasteners & Check For Fuel Leaks: Press injectors into cylinder head bores. Torque fuel rail retaining bolts to 10 N·m. Tighten high pressure line to 28 N·m. Prime system and inspect for leaks.
- Verify part number 12698552 and the listed cross references before fitting.
- Torque the injector mounting/hold-down fasteners to 10 N·m.
- Torque the high-pressure line to 28 N·m.
Frequently Asked Questions
Which vehicles and engine family does part number 12698552 fit?
It is listed for the GM 2.0L Ecotec Turbo SIDI engine family (LTG / LSY Tripower / LHU), including Cadillac CT5 2.0L LSY Turbo 174kW (2020-2024), Cadillac XT4 2.0L LSY Turbo 174kW (2019-2024), and Buick Envision II 2.0L LSY Turbo 174kW (2021-2024). This common-rail diesel injector is listed with a system pressure of 350 bar. Confirm exact vehicle fitment against the vehicle's EPC before ordering.
How can I verify the old injector before replacement?
Check the old unit against part number 12698552 and the other listed cross references: 12707255, 0261500690, 0261500691, 05E906036C, and 06M906036AD. If the marking does not match, confirm the correct part against the vehicle's EPC.
What diagnostic trouble codes are listed for this injector?
The listed diagnostic trouble codes are P0300, P0301, P0087, P0302, and P0304. Any additional diagnostic criteria or symptom interpretation is not stated and must be confirmed against the vehicle's EPC.
Does this injector need coding/adaptation, and can the seals be reused?
Coding/adaptation requirements and seal reuse are not stated in the provided facts; both must be confirmed against the vehicle's EPC. The injector mounting/hold-down torque is 10 N·m, and the high-pressure line torque is 28 N·m.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.