HITACHI 12634491
High Pressure Fuel Pump Chevy Camaro Buick Regal Cadillac ATS CTS 2.0T LTG HPP0008
12658339, 12651170, HPP0008, HM10014, GDP104, 12641847--150 bar peak rail pressureProduct Overview
The 12634491 is an original equipment (HITACHI) precision component engineered specifically for the GM 2.0L Ecotec Turbo SIDI DOHC (LTG). Operating at peak injection pressures up to 150 bar (2175 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P0089, P0171.
Always verify the OE reference 12658339, 12651170, HPP0008, HM10014 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 12634491 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 12634491 |
| Manufacturer Brand | HITACHI |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | GM 2.0L Ecotec Turbo SIDI DOHC (LTG) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 13 N-m (115 lb-in) |
| Fuel Line / Rail Torque | 30 N-m (22 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P0089, P0171 |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 13 N-m (115 lb-in), and torque fuel line fittings to 30 N-m (22 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Tighten the pump mounting/hold-down fasteners to 13 N·m.
- Tighten the high-pressure line to 30 N·m.
- Confirm seal reuse and any coding or adaptation requirements against the vehicle's EPC before installation.
Frequently Asked Questions
Will part number 12634491 fit my Cadillac ATS?
Part number 12634491 is listed for Cadillac ATS / ATS-L with the LTG, LSY, or LHU engine from 2013 to 2019. Confirm the exact engine code and model year against the vehicle's EPC before ordering.
What trouble codes are associated with this high-pressure fuel pump?
The listed diagnostic trouble codes are P0300, P0087, P0193, P0089, and P0191. Use these codes with proper diagnostics, and confirm any symptom against the vehicle's service information because no symptom descriptions are provided.
Does this pump require coding or adaptation after installation?
The provided facts do not state coding or adaptation requirements for this pump. Confirm any coding or adaptation procedure against the vehicle's EPC or service information instead of guessing.
How can I verify the old high-pressure fuel pump part number?
Compare the old unit against the listed cross references: 12634491, 12658339, 12651170, HPP0008, HM10014, and GDP104. If the markings are unclear, confirm fitment against the vehicle's EPC.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.